mypros+
Error code reference

Electrolux Dryer Error Code BE

Line safe error

Electrolux codesElectrolux dryer codes

Line safe error — line safe relay problem (main board failure).

First step from the service manual

Replace main board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for BE.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What BE means on a Electrolux dryer

The BE error code on an Electrolux dryer indicates a line safe relay fault originating on the main control board. The line safe relay is a critical safety component integrated into the main board circuit. Its function is to interrupt power flow to the dryer's heating system or motor circuit under conditions that could pose an electrical hazard. When the dryer's control system detects an abnormal state in this relay, such as a failure to open or close on command, or an inconsistent signal from the relay's feedback circuit, the BE code is triggered and normal operation is halted.

Because the line safe relay is physically part of the main control board assembly rather than a standalone serviceable component, a fault in this relay is treated as a main board failure. The relay itself may have developed a welded contact, a failed coil, or degraded switching characteristics. In some cases, a power surge or voltage fluctuation from the home's electrical supply can damage the relay or the board circuitry supporting it, making the fault appear suddenly without prior symptoms.

The diagnostic path for BE is direct: the main control board requires replacement. There are no external wiring harnesses or sensors associated with the line safe relay that would warrant inspection first, since the fault is internal to the board. Attempting to reset the error without replacing the board may temporarily clear the code, but the fault condition will typically return because the underlying hardware defect remains present.

Source: manufacturer service documentation.

Common causes of BE

  1. 01

    Failed line safe relay on main board

    Part replacement

    The relay integrated into the main control board has failed internally, with a welded contact, open coil, or degraded switching function. This is the primary cause of the BE code and requires replacing the entire main board assembly.

  2. 02

    Power surge or voltage spike damage

    Part replacement

    A surge from the home's electrical supply can damage the relay circuit or surrounding board components. If the BE code appeared suddenly after a power event, surge damage to the board is a likely contributor.

  3. 03

    General main board failure

    Part replacement

    Beyond the relay itself, broader failure of the main control board can cause the relay monitoring circuit to report a fault. Burn marks, cracked solder joints, or failed capacitors on the board may be visible upon inspection.

  4. 04

    Intermittent board connection or power supply issue

    Wiring / connection

    In rare cases, an unstable power supply to the board can cause the relay status to read incorrectly. Verifying that the dryer is receiving correct line voltage at the terminal block is a reasonable preliminary check before board replacement.

See the test procedure for each cause

Frequently asked questions about BE

What does BE mean on a Electrolux dryer?
The BE code indicates a line safe relay error, which is a fault detected in the safety relay circuit located on the main control board. This relay is responsible for safely controlling power delivery within the dryer. Because the relay is part of the main board and not a separate component, the board itself must be replaced to resolve the fault.
Can I fix the BE error myself on an Electrolux dryer?
Replacing the main control board is within the capability of a technically confident DIYer who is comfortable working with appliance electronics and disconnecting power safely. The repair involves accessing the board, disconnecting all wiring harnesses, and installing the replacement board. However, if you are unsure about working with high-voltage appliance components, a qualified technician is the safer choice.
Is it safe to use my Electrolux dryer when the BE code is displayed?
No, you should not operate the dryer while the BE error is active. The line safe relay is a protective component, and a fault in this circuit means the dryer's electrical safety system is not functioning correctly. Continued use could pose an electrical hazard, and the dryer will typically refuse to run normally until the fault is resolved.
Will resetting my Electrolux dryer clear the BE error code?
A reset may temporarily clear the BE code from the display, but it will not resolve the underlying hardware fault in the main control board. Because the line safe relay failure is a physical defect within the board, the error will return once the dryer attempts to operate again. Board replacement is required for a permanent fix.
How much does it cost to repair a BE error on an Electrolux dryer?
The cost of repairing a BE error depends on whether you hire a technician or do the work yourself. A replacement main control board typically costs in the range of $80 to $250 for the part alone, depending on the specific model. Professional repair, including parts and labor, generally falls in the range of $150 to $400. Getting a repair quote before proceeding helps determine whether repair or replacement of the dryer makes more financial sense.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass