mypros+
Error code reference

Electrolux Dryer Error Code BD

Line safe relay short circuit error.

Electrolux codesElectrolux dryer codes

Line safe relay short circuit error.

First step from the service manual

Line safe relay problem — replace main board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for BD.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What BD means on a Electrolux dryer

The BD error code on an Electrolux dryer indicates a line safe relay short circuit error. The line safe relay is a critical safety component located on the main control board. Its primary function is to interrupt power to the heating circuit or drive motor under specific fault conditions, preventing unsafe operation. When the control board detects that this relay has shorted internally, it triggers the BD code and halts dryer operation to protect both the appliance and the user.

A shorted relay means the relay contacts are stuck in a closed position, or an internal fault within the relay is causing unintended electrical continuity. This is distinct from an open circuit failure. Because the line safe relay is integrated into the main control board assembly rather than being a standalone field-replaceable component, diagnosing this fault at the component level is not practical for most repair scenarios. The control board must be evaluated as a unit.

The primary and recommended corrective action for a BD error is replacement of the main control board. There are no reset procedures or external wiring checks that will resolve an internally shorted relay. Continuing to operate the dryer with this fault present is not recommended, as the relay's safety function is compromised. When sourcing a replacement board, confirm compatibility using the dryer's full model number found on the door frame rating label.

Source: manufacturer service documentation.

Common causes of BD

  1. 01

    Failed line safe relay on main control board

    Part replacement

    The relay integrated into the main control board has shorted internally, which is the direct cause of the BD error. This is the most common and essentially only identified cause for this specific code, and it requires main board replacement.

  2. 02

    Electrical surge or power spike damage

    Part replacement

    A voltage surge from the power supply can damage relay components on the control board, causing an internal short. Inspect the dryer's power cord and outlet for signs of burn marks or damage as a secondary check.

  3. 03

    Prolonged overheating of the control board

    Part replacement

    Excessive heat in the control board area over time can degrade relay components and cause them to fail in a shorted state. Check that the dryer's exhaust venting is clear and unrestricted to avoid heat buildup.

See the test procedure for each cause

Frequently asked questions about BD

What does BD mean on a Electrolux dryer?
The BD error code on an Electrolux dryer indicates a line safe relay short circuit error. The line safe relay is a safety component on the main control board that has been detected as shorted. Because this relay is part of the main board assembly, the board itself must be replaced to resolve the fault.
Can I fix the BD error myself on my Electrolux dryer?
The repair requires replacing the main control board, which is a task that intermediate-to-advanced DIYers can attempt if they are comfortable working with appliance electrical components. The board must be matched to your dryer's specific model number. If you are not confident working around high-voltage components, hiring a qualified appliance technician is the safer choice.
Is it safe to use my Electrolux dryer while it shows the BD error?
No, you should not continue using the dryer while the BD code is active. The line safe relay is a protective component, and operating the dryer with this relay in a shorted state means that safety function is no longer working correctly. Stop using the dryer until the main control board has been replaced.
Will resetting my Electrolux dryer clear the BD error code?
No, resetting the dryer will not clear the BD error code or fix the underlying problem. Because the fault is caused by an internal short circuit within the line safe relay on the main control board, the issue is a hardware failure. The error will return immediately or upon the next startup until the main control board is replaced.
How much does it cost to fix the BD error on an Electrolux dryer?
The cost depends on whether you repair it yourself or hire a technician. A replacement main control board for an Electrolux dryer typically ranges from $100 to $250 or more depending on the model. If you use a professional repair service, expect to add $75 to $150 or more in labor costs, bringing the total repair estimate to roughly $175 to $400 or higher.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass