mypros+
Error code reference

Electrolux Dryer Error Code 92

User Interface mother board protocol mismatch.

Electrolux codesElectrolux dryer codes

User Interface mother board protocol mismatch.

First step from the service manual

Check for wiring failure, user interface board failure, or main board failure.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 92.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 92 means on a Electrolux dryer

Error code 92 on an Electrolux dryer indicates a protocol mismatch between the user interface board and the main control board. These two boards communicate with each other over a defined digital communication protocol, and when the data being exchanged does not conform to the expected format or version, the system flags this error. This typically means the two boards are not speaking the same communication language, often because one board has been replaced with an incompatible version, or because the communication link between them has been disrupted.

The most common trigger for this error is a wiring failure between the user interface board and the main board. Damaged, corroded, or loose connector pins can corrupt the data signal enough to cause a protocol mismatch without fully breaking the circuit. A failed user interface board that is sending malformed data packets, or a failed main control board that cannot correctly interpret incoming signals, will produce the same result.

Diagnosis should begin by inspecting the wiring harness that runs between the two boards, looking for pinched wires, loose connectors, or corrosion at the terminal pins. If the wiring is intact, the user interface board is statistically more likely to be the failed component than the main board, but both must be considered. Confirming that replacement boards carry compatible firmware versions is also critical before substitution testing.

Source: manufacturer service documentation.

Common causes of 92

  1. 01

    Wiring harness failure between boards

    Wiring / connection

    A damaged, pinched, or corroded wire connector between the user interface board and the main control board can corrupt the communication signal. Inspect the full length of the harness and check terminal pins for corrosion or looseness.

  2. 02

    Failed user interface board

    Part replacement

    The user interface board can fail in a way that sends malformed or out-of-spec data to the main control board, triggering the mismatch error. This is often identifiable when the display behaves erratically or buttons stop responding.

  3. 03

    Failed main control board

    Part replacement

    If the main board cannot correctly process incoming signals from the user interface board, a protocol mismatch will be logged. This is less common than a UI board failure but should be tested after ruling out wiring and the UI board.

  4. 04

    Incompatible replacement board installed

    Part replacement

    If either the main board or the user interface board was recently replaced with a version carrying a different firmware or communication protocol version, a mismatch will occur. Confirm compatibility before installing any replacement control board.

See the test procedure for each cause

Frequently asked questions about 92

What does 92 mean on a Electrolux dryer?
Error code 92 means there is a protocol mismatch between the user interface board and the main control board. The two boards communicate digitally, and when that communication does not match the expected format, the dryer flags this code. The cause is typically a wiring failure or a fault in one of the two control boards.
Can I fix error code 92 on my Electrolux dryer myself?
A knowledgeable DIYer can start by inspecting the wiring harness between the two control boards for loose connectors, damaged wires, or corroded terminals, as this requires no parts and may resolve the issue. If the wiring is intact, replacing one of the control boards is the next step, which is more involved but achievable with basic appliance repair skills. If you are not comfortable working with electronic control boards, a qualified technician is recommended.
Will resetting my Electrolux dryer clear error code 92?
A power reset may temporarily clear the code, but if an underlying wiring fault or board failure is present, the error will return once the dryer attempts to resume normal operation. A reset is a useful first step to confirm whether the error is intermittent, but it is not a fix for the root cause.
Is it safe to use my Electrolux dryer when error code 92 is showing?
Error code 92 indicates a communication failure between control boards, and the dryer will typically not operate normally while this code is active. Attempting to force operation without resolving the fault is not recommended, as the control system cannot reliably manage dryer functions without proper board-to-board communication.
How much does it cost to repair error code 92 on an Electrolux dryer?
If the fix is a wiring connector repair, costs can be minimal, generally in the range of a few dollars for terminals or connectors plus labor time. A replacement user interface board typically costs between $80 and $200 for the part, while a main control board can range from $100 to $300 or more depending on the model. Professional diagnostic and labor fees will add to these estimates.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass