mypros+
Error code reference

Electrolux Dryer Error Code HF

Line safe sensing error

Electrolux codesElectrolux dryer codes

Line safe sensing error — line safe sensing circuit failure (main board failure).

First step from the service manual

Replace main board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for HF.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What HF means on a Electrolux dryer

The HF error code on an Electrolux dryer indicates a line safe sensing circuit failure. This circuit is part of the main control board and is responsible for monitoring the incoming power line to ensure the dryer is receiving safe, stable electrical input. When the board detects an anomaly or complete failure within this sensing circuit, it triggers the HF code and halts operation as a protective measure.

The line safe sensing function is integrated directly into the main control board's circuitry. Unlike errors tied to external sensors or wiring harnesses, the HF code points specifically to an internal circuit failure on the board itself. This means the fault is not caused by a loose wire, a failed thermistor, or a separate external component. The sensing circuit monitors line voltage conditions, and when that circuit malfunctions internally, the board can no longer verify safe operating conditions.

Because the fault originates within the main control board, the primary and recommended diagnostic step is replacement of the board. There are no external components to test or swap before addressing the board itself. Technicians should confirm the dryer is receiving proper line voltage at the terminal block before condemning the board, to rule out a facility-level power issue that might contribute to board stress or failure. Once proper incoming voltage is confirmed, replacing the main control board is the correct course of action.

Source: manufacturer service documentation.

Common causes of HF

  1. 01

    Main control board failure

    Part replacement

    The line safe sensing circuit is built into the main control board, and an internal failure of this circuit is the direct cause of the HF code. Replacement of the board is the required fix.

  2. 02

    Power surge or voltage spike damage

    Part replacement

    A sudden surge in line voltage can damage the sensitive circuitry on the main control board, causing the line safe sensing circuit to fail. If the dryer was recently exposed to a power outage or surge event, this is a likely contributor.

  3. 03

    Sustained overvoltage or undervoltage at the outlet

    Wiring / connection

    Chronic voltage irregularities from the home's electrical supply can stress the control board over time and eventually cause internal circuit failure. Verify the dryer outlet is supplying the correct voltage before installing a replacement board.

  4. 04

    Moisture or contaminant intrusion on the board

    Part replacement

    Condensation or lint buildup on the control board can cause short circuits or corrosion that damages the sensing circuit. Inspect the board carefully for visible burn marks, corrosion, or debris when replacing it.

See the test procedure for each cause

Frequently asked questions about HF

What does HF mean on a Electrolux dryer?
HF on an Electrolux dryer stands for a line safe sensing error, meaning the line safe sensing circuit on the main control board has failed. This circuit monitors the incoming electrical power supply to the dryer. Because the fault is internal to the main board, the board must be replaced to resolve the error. There is no external sensor or wiring fix that will clear a true HF fault.
Can I fix the HF error code myself on an Electrolux dryer?
A knowledgeable DIYer comfortable working with appliance electronics can replace the main control board themselves. Before ordering a board, verify that the dryer's power outlet is supplying correct voltage, since a facility-level power problem could stress or damage a new board. If the outlet checks out, replacing the main control board is the repair. Make sure to disconnect power to the dryer completely before handling the board.
Is it safe to use my Electrolux dryer when the HF code is displayed?
No, you should not operate the dryer while the HF error is active. The line safe sensing circuit exists to verify safe electrical conditions before allowing the dryer to run. With that circuit failed, the board cannot confirm safe operating conditions, and running the appliance presents a potential electrical risk. Leave the dryer unplugged until the main control board has been replaced.
Will resetting my Electrolux dryer clear the HF error code?
A simple reset, such as unplugging the dryer and plugging it back in, will not permanently clear the HF code. Because the fault is an internal hardware failure within the main control board's sensing circuit, the error will return as soon as the dryer powers up and the board attempts to run its sensing function again. The only lasting fix is replacing the failed main control board.
How much does it cost to repair an Electrolux dryer with an HF error code?
The cost to repair an HF error on an Electrolux dryer depends on the price of the replacement main control board and whether you hire a technician or do the repair yourself. Main control boards for Electrolux dryers typically range from $100 to $250 or more depending on the model. If you hire a professional appliance technician, labor charges will add roughly $75 to $150 on top of the part cost, bringing the total repair estimate to somewhere between $175 and $400.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass