mypros+
Error code reference

Electrolux Dryer Error Code 0x92

User Interface Protocol Incongruence Error

Electrolux codesElectrolux dryer codes

User Interface Protocol Incongruence Error – Main Board incompatible with User Interface Board.

First step from the service manual

Check if correct User Interface Board and Main Board are installed; replace respective board if incorrect configuration.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 0x92.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 0x92 means on a Electrolux dryer

Error code 0x92 on an Electrolux dryer indicates a User Interface Protocol Incongruence Error. This fault is triggered when the main control board and the user interface (UI) board are unable to communicate using a compatible protocol. These two boards must be matched to the same appliance platform and firmware generation. When the dryer detects a mismatch during the communication handshake between the two boards, it flags this error and typically prevents normal operation.

The most common trigger for this error is an incorrect replacement board being installed during a prior repair. If a technician installed a main board or UI board sourced from a different model variant or a different production revision, the two boards may not share the same communication protocol, even if the physical connectors appear identical. This is a strictly electronic incompatibility, not a wiring or connector failure.

Diagnosing this error requires confirming that both the main board and the UI board carry matching part numbers and are specified for the exact model being serviced. If either board was recently replaced, that is the most likely source of the mismatch. In some cases, a board may have been installed from a different production run that uses an updated protocol version incompatible with the other board currently in the unit. The resolution is to identify which board is incorrect and replace it with one that matches the other board's protocol requirements for the specific dryer model.

Source: manufacturer service documentation.

Common causes of 0x92

  1. 01

    Mismatched replacement board installed

    Part replacement

    The most frequent cause is a main board or UI board that was replaced during a previous repair with a part intended for a different model or revision. Even boards with identical connectors can use incompatible communication protocols.

  2. 02

    UI board from a different production revision

    Part replacement

    Updated production runs of a board may use a revised communication protocol that is not backward compatible. If a newer revision board was sourced as a replacement, it may not communicate correctly with the older board still in the unit.

  3. 03

    Main board from a different production revision

    Part replacement

    The same revision mismatch can occur on the main board side. If the main board was replaced with a unit from a different revision tier, it may fail the protocol handshake with the original UI board.

  4. 04

    Incorrect board installed during factory or warranty service

    Part replacement

    In rare cases, an incorrect board may have been installed before the unit reached the customer. Verifying part numbers on both boards against the dryer model is the key diagnostic step.

See the test procedure for each cause

Frequently asked questions about 0x92

What does 0x92 mean on a Electrolux dryer?
Error code 0x92 indicates a User Interface Protocol Incongruence Error, meaning the main control board and the user interface board installed in the dryer are not compatible with each other. The two boards communicate using a specific protocol, and when they do not match, the dryer logs this fault. This is typically the result of an incorrect replacement board being installed at some point. Normal operation is usually disrupted until the incompatible board is identified and replaced with the correct version.
Can I fix error code 0x92 myself on my Electrolux dryer?
Fixing this error requires identifying which board, the main board or the UI board, does not match the dryer's requirements, which involves checking part numbers and compatibility for your specific model. If you are comfortable working with appliance electronics and can source the correct replacement board, this is a repair a knowledgeable DIYer can attempt. However, incorrectly identifying or ordering the wrong board will not resolve the issue and may add cost. If you are unsure, a qualified appliance technician is the safer option.
Is it safe to use my Electrolux dryer when error code 0x92 is showing?
A 0x92 error indicates a fundamental communication failure between two control boards, and the dryer will typically not operate normally when this fault is active. Attempting to force operation in this state is not recommended. You should avoid using the dryer until the board incompatibility is resolved to prevent any risk of unexpected behavior from the uncoordinated control systems.
Will resetting my Electrolux dryer clear error code 0x92?
Resetting the dryer, such as by unplugging it or cycling the power, will not resolve error code 0x92. This fault is caused by a hardware incompatibility between two installed boards, not a temporary software glitch. The error will return immediately upon power-up as long as the mismatched boards are still installed. The only resolution is to replace the incorrect board with a properly matched part.
How much does it cost to repair error code 0x92 on an Electrolux dryer?
The cost to repair a 0x92 error depends on which board needs to be replaced, the main board or the UI board, and whether you use a professional technician or perform the repair yourself. Control board parts for Electrolux dryers typically range from around 80 dollars to over 250 dollars depending on the specific board. Adding professional labor, total repair costs commonly fall in the range of 150 dollars to 400 dollars or more. Getting a firm quote from a technician after they confirm which board is incorrect will give you the most accurate estimate.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass