mypros+
Error code reference

Electrolux Dryer Error Code 0x91

User Interface Communication Error

Electrolux codesElectrolux dryer codes

User Interface Communication Error – User Interface Board defective or Main Board defective or Wiring defective.

First step from the service manual

Check wiring continuity between Main Board and User Interface Board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 0x91.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 0x91 means on a Electrolux dryer

Error code 0x91 on an Electrolux dryer indicates a User Interface Communication Error. This fault occurs when the main control board loses reliable communication with the user interface (UI) board, which is the control panel assembly that houses the buttons, knobs, and display. These two boards continuously exchange data signals during operation, and when that communication link breaks down or produces invalid responses, the dryer's control system flags the 0x91 fault and halts normal operation to prevent unintended behavior.

The three primary causes identified for this code are a defective user interface board, a defective main control board, or wiring problems between the two components. Wiring issues are the most common starting point for diagnosis because connection failures, corroded terminals, pinched wires, or loose harness connectors can interrupt the communication signals without either board being at fault. A thorough continuity check of the wiring harness running between the main board and the UI board is the recommended first diagnostic step.

If wiring continuity checks out and all connectors are seated properly, the fault points to one of the two boards. Determining which board has failed can require substitution testing or the use of a diagnostic multimeter to verify signal output at the board connectors. The UI board is statistically more likely to fail due to user contact and humidity exposure, but the main board cannot be ruled out until wiring has been confirmed intact.

Source: manufacturer service documentation.

Common causes of 0x91

  1. 01

    Loose or damaged wiring harness

    Wiring / connection

    The wiring harness connecting the main board to the user interface board may have a loose connector, broken wire, or corroded terminal that interrupts communication signals. Inspect all connectors along this harness for secure seating and visible damage, and use a multimeter to verify continuity across each wire.

  2. 02

    Defective user interface board

    Part replacement

    The user interface board can fail due to moisture exposure, physical damage from button use, or internal component failure, causing it to stop responding to the main board. If wiring checks out, the UI board is the most likely component to replace.

  3. 03

    Defective main control board

    Part replacement

    The main control board may have failed internally and lost the ability to send or receive communication signals to the UI board. This is typically diagnosed after wiring and the UI board have been ruled out as the source of the fault.

  4. 04

    Corroded or oxidized connector pins

    Wiring / connection

    Even if wires are intact, connector pins between the boards can develop corrosion or oxidation that raises resistance and degrades signal quality enough to trigger a communication fault. Inspect the connector pins closely and clean or reseat them as needed.

See the test procedure for each cause

Frequently asked questions about 0x91

What does 0x91 mean on a Electrolux dryer?
Error code 0x91 on an Electrolux dryer indicates a User Interface Communication Error. This means the main control board and the user interface board are not communicating properly. The fault is caused by defective wiring between the boards, a failed user interface board, or a failed main control board. The dryer will typically stop operating until the underlying issue is resolved.
Can I fix the 0x91 error myself on my Electrolux dryer?
A knowledgeable DIYer can begin by checking the wiring harness between the main board and the user interface board for loose connectors, broken wires, or corrosion, as this is the first recommended diagnostic step. If the wiring is intact and connectors are secure, replacing one of the two boards is the next step, which requires disassembling the dryer's control panel area. If you are not comfortable working with appliance electronics or disassembling control components, a qualified technician is recommended.
Is it safe to use my Electrolux dryer when error code 0x91 is displayed?
The dryer should not be operated while displaying a 0x91 communication fault, as the control system cannot reliably process inputs or monitor the machine's operating state. Running the dryer in this condition could lead to unpredictable behavior. Power down the appliance and have the fault diagnosed before resuming use.
How much does it cost to repair error code 0x91 on an Electrolux dryer?
Repair costs vary depending on which component is at fault. If the issue is a simple wiring or connector problem, costs may be limited to a service call fee, typically in the range of $75 to $150. A replacement user interface board or main control board can add $100 to $350 or more in parts, plus labor costs if a technician performs the repair.
Will resetting my Electrolux dryer clear the 0x91 error code?
Unplugging the dryer for a few minutes and restoring power may temporarily clear the 0x91 code, but if the underlying wiring or board fault is still present, the error will return. A reset does not repair damaged wiring, corroded connectors, or a faulty board. Persistent or recurring 0x91 errors require physical inspection and component testing to resolve permanently.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass