mypros+
Error code reference

Electrolux Dryer Error Code 0x59

FCV Motor Not Following

Electrolux codesElectrolux dryer codes

FCV Motor Not Following – Main board defective.

First step from the service manual

Replace the Main Board and repeat the diagnostic cycle to check for any further errors.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 0x59.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 0x59 means on a Electrolux dryer

Error code 0x59 on an Electrolux dryer indicates an FCV Motor Not Following fault. The FCV (Flow Control Valve) motor is responsible for managing airflow or gas flow within the dryer's control system. When the main board sends a command signal to the FCV motor and does not receive the expected feedback confirming the motor has responded or moved to the correct position, the 0x59 fault is triggered. This mismatch between the commanded output and the actual motor response is what the control board interprets as a "not following" condition.

The primary cause identified for this fault is a defective main control board rather than the FCV motor itself. The main board both generates the control signal and monitors the response. If the board's internal circuitry responsible for driving or reading back the FCV motor signal has failed, the board may incorrectly report a motor fault even when the motor is functioning properly. This makes the main board the first component to address rather than immediately replacing the motor.

Diagnosing this fault begins with replacing the main control board and running the dryer through a full diagnostic cycle to confirm whether the error clears and does not return. If the 0x59 code persists after a verified main board replacement, attention should then shift to inspecting the FCV motor itself, the wiring harness connecting the motor to the board, and any associated connectors for damage, corrosion, or poor contact.

Source: manufacturer service documentation.

Common causes of 0x59

  1. 01

    Defective Main Control Board

    Part replacement

    The main board is the primary suspect for this fault, as it both sends commands to the FCV motor and reads the response. A failed driver circuit or feedback monitoring circuit on the board produces a false not-following error.

  2. 02

    Damaged Wiring Harness or Connector

    Wiring / connection

    A broken wire, corroded pin, or loose connector between the main board and the FCV motor can interrupt the signal path and trigger this fault. Inspect the harness and connectors for visible damage or poor seating.

  3. 03

    Faulty FCV Motor

    Part replacement

    If the main board is replaced and the error continues, the FCV motor itself may be mechanically seized or electrically open. This should be evaluated after ruling out the main board.

  4. 04

    Intermittent Electrical Connection

    Wiring / connection

    Vibration during operation can cause connectors to work loose over time. A connector that appears seated may still have poor contact under load, producing inconsistent motor feedback signals.

See the test procedure for each cause

Frequently asked questions about 0x59

What does 0x59 mean on a Electrolux dryer?
Error code 0x59 on an Electrolux dryer means the FCV Motor Not Following fault has been detected. The main control board sent a command to the FCV motor but did not receive the expected feedback confirming the motor responded. This fault is attributed to a defective main control board in most cases. The dryer will need the main board replaced and a diagnostic cycle run to confirm the repair.
Can I fix error code 0x59 myself?
Replacing the main control board is within the range of a skilled DIYer who is comfortable working with appliance electronics and disconnecting power before servicing. The repair involves accessing the control board, disconnecting the wiring harness connections, and installing the replacement board. After replacement, a diagnostic cycle should be run to confirm the error does not return. If you are not comfortable working around electrical components, a qualified technician is recommended.
Is it safe to keep using my Electrolux dryer when error 0x59 appears?
It is not recommended to continue operating the dryer while this fault is active. The FCV motor controls airflow or gas flow within the system, and an unresolved fault in that circuit could affect the dryer's safe operation. You should stop using the dryer until the main board has been inspected and replaced as needed.
Will resetting my Electrolux dryer clear the 0x59 error code?
A power reset may temporarily clear the error code from the display, but it will not resolve the underlying fault. If the main control board is defective, the 0x59 code will return once the dryer runs through its cycle again and the board fails to properly communicate with the FCV motor. A proper repair requires replacing the faulty component.
How much does it cost to repair error code 0x59 on an Electrolux dryer?
The cost of repair depends primarily on the price of the replacement main control board and whether you use a technician or complete the repair yourself. Main control boards for Electrolux dryers typically range from $100 to $250 or more depending on the model. If you hire a technician, labor costs can add $75 to $200 or more on top of the part price. DIY replacement can significantly reduce the total cost.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass