mypros+
Error code reference

Electrolux Dryer Error Code 0xF6

Safety Reset Error

Electrolux codesElectrolux dryer codes

Safety Reset Error – Main board defective.

First step from the service manual

Replace the Main Board and repeat the diagnostic cycle to check for any further errors.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 0xF6.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 0xF6 means on a Electrolux dryer

The 0xF6 error code on an Electrolux dryer indicates a Safety Reset Error caused by a defective main control board. The main board is the central processing unit of the dryer, responsible for managing all operational cycles, monitoring sensor inputs, regulating heating elements, and executing safety shutoffs. When the board becomes defective, it may fail to properly execute or recover from a safety reset sequence, triggering this fault code to prevent unsafe operation.

This error differs from soft faults that can be cleared through a power cycle. The 0xF6 code specifically points to an internal failure within the main board itself, such as corrupted firmware, failed onboard components, or damaged circuitry that prevents the board from completing its safety reset protocol. External factors such as power surges, moisture exposure, or heat damage to the board can cause these types of internal failures.

Because the root cause is the main board itself, standard troubleshooting steps like resetting the dryer or checking external wiring connections will not resolve this fault. The diagnostic process should begin with replacing the main control board and then running a full diagnostic cycle afterward to confirm the error is cleared and to check whether any additional fault codes are present. Until the board is replaced, the dryer should not be operated due to the safety implications of a non-functional control system.

Source: manufacturer service documentation.

Common causes of 0xF6

  1. 01

    Failed Main Control Board

    Part replacement

    The primary and most direct cause of 0xF6 is an internally defective main board that cannot complete its safety reset sequence. This is not resolvable through resets or external repairs and requires board replacement.

  2. 02

    Power Surge Damage

    Part replacement

    A voltage spike from a power surge can damage onboard components of the main control board, causing it to malfunction and trigger the safety reset error. Check for signs of burn marks or discoloration on the board.

  3. 03

    Heat or Moisture Damage to the Board

    Part replacement

    Prolonged exposure to excess heat from a restricted exhaust vent or moisture infiltration can degrade the main board's circuitry over time. Inspect the board for corrosion, warping, or discoloration.

  4. 04

    Corrupted Board Firmware

    Part replacement

    In some cases, the board's internal firmware can become corrupted, preventing it from completing operational or safety reset routines. This condition is not field-repairable and the board must be replaced.

See the test procedure for each cause

Frequently asked questions about 0xF6

What does 0xF6 mean on a Electrolux dryer?
The 0xF6 code on an Electrolux dryer indicates a Safety Reset Error, meaning the main control board has been identified as defective. The main board manages all dryer functions and safety protocols, and when it fails internally, the dryer triggers this fault and stops operating. This error code points directly to the board itself, not to any external wiring or sensor components.
Can I fix the 0xF6 error on my Electrolux dryer myself?
Resolving the 0xF6 error requires replacing the main control board, which involves disconnecting wiring harnesses and mounting a new board inside the dryer cabinet. Experienced DIYers comfortable with appliance repair can perform this replacement, but if you are unsure about working with appliance electronics, a qualified technician is recommended. After replacing the board, a full diagnostic cycle should be run to confirm the error is cleared.
Is it safe to keep using my Electrolux dryer with the 0xF6 error?
No, the dryer should not be operated while displaying the 0xF6 error. A defective main control board means the dryer's safety reset functions are not working correctly, which could lead to uncontrolled operation or failure to respond to critical safety shutoff commands. Discontinue use until the board has been replaced.
How much does it cost to fix the 0xF6 error on an Electrolux dryer?
The cost to repair the 0xF6 error depends primarily on the price of the replacement main control board and labor if a technician is hired. Main control boards for Electrolux dryers typically range from $100 to $300 or more depending on the model. Adding professional labor, total repair costs generally range from $200 to $500. Comparing this to the cost of a replacement dryer can help determine if repair is worthwhile.
Will resetting my Electrolux dryer clear the 0xF6 error code?
No, a standard power cycle or reset will not clear the 0xF6 error. This fault code indicates that the main board itself is defective, meaning the underlying hardware failure persists regardless of resets. The error will return until the main control board is physically replaced and the dryer passes a diagnostic cycle.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass