mypros+
Error code reference

Electrolux Dryer Error Code 41

Door opened at cycle start.

Electrolux codesElectrolux dryer codes

Door opened at cycle start.

First step from the service manual

Refer to test (10)

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 41.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 41 means on a Electrolux dryer

Error code 41 on an Electrolux dryer indicates that the door was detected as open at the beginning of a drying cycle. The control board monitors the door switch circuit continuously and expects the door to be fully latched before initiating or maintaining a cycle. When the control detects an open door signal at cycle start, it halts operation and stores this fault code to alert the technician to a problem in the door latch or switch circuit.

The primary components involved are the door switch assembly, the door latch mechanism, and the wiring harness connecting the switch to the main control board. The door switch is typically a normally open or normally closed contact that changes state when the door is properly latched. If the switch fails to send the correct closed-circuit signal, the control board interprets this as an open door condition even if the door appears physically shut.

Diagnostic work for this code begins with Test 10 as outlined in the Electrolux service procedure. This test isolates the door switch circuit to determine whether the fault originates with the switch itself, the latch mechanism preventing full switch actuation, or a wiring issue such as a broken wire or loose connector. Technicians should inspect the door strike, the latch catch, and the switch terminals for continuity before concluding the switch requires replacement.

Source: manufacturer service documentation.

Common causes of 41

  1. 01

    Faulty door switch

    Part replacement

    The door switch may have failed and is not sending a closed-circuit signal to the control board when the door is latched. Checking the switch for continuity with a multimeter will confirm whether it is functioning correctly.

  2. 02

    Worn or broken door latch

    Part replacement

    If the door latch or strike is worn, broken, or misaligned, the door may not close far enough to fully actuate the door switch. Inspect the latch and strike for visible damage or misalignment.

  3. 03

    Loose or damaged wiring connector

    Wiring / connection

    A loose, corroded, or broken connector at the door switch or along the harness between the switch and control board can interrupt the circuit. Inspect all connectors and wiring in the door switch circuit for damage or poor seating.

  4. 04

    Door not fully closed by the user

    Wiring / connection

    Occasionally the error is triggered simply because the door was not pushed firmly shut before starting the cycle. Attempting to close the door securely and restarting the cycle will resolve this if no component has failed.

  5. 05

    Control board not reading switch signal correctly

    Part replacement

    In less common cases, the main control board may fail to correctly interpret the door switch signal even when the switch and wiring are intact. This is typically diagnosed only after the switch and wiring have been confirmed good.

See the test procedure for each cause

Frequently asked questions about 41

What does 41 mean on a Electrolux dryer?
Error code 41 means the dryer detected an open door condition at the start of a cycle. The control board monitors the door switch circuit and will not allow the dryer to run if it does not receive a signal confirming the door is latched. This can be caused by a faulty door switch, a broken latch, or a wiring problem in the door switch circuit.
How do I fix error code 41 on my Electrolux dryer?
Start by firmly closing the door and attempting to restart the cycle to rule out an accidental trigger. If the code returns, the recommended first step is to perform Test 10 from the Electrolux service procedure, which checks the door switch circuit. From there, inspect the door switch for continuity, examine the latch and strike for wear or misalignment, and check all wiring connectors in the door switch circuit.
Is it safe to use my Electrolux dryer when error code 41 appears?
The dryer is designed to prevent operation when this code is active, so it will not run until the door circuit issue is resolved. You should not attempt to bypass the door switch, as the door interlock is a safety feature that prevents the drum from spinning with the door open. Address the underlying cause before using the dryer.
Will resetting my Electrolux dryer clear error code 41?
A reset may temporarily clear the code, but if the door switch, latch, or wiring has a real fault, the code will return when you attempt to start another cycle. A reset is only a lasting fix if the door was simply not fully closed when the code first appeared. If the code comes back after a reset, further diagnosis of the door switch circuit is needed.
How much does it cost to repair error code 41 on an Electrolux dryer?
If only a door switch replacement is needed, parts typically range from around $10 to $40 depending on the model, with professional labor adding $75 to $150 or more. A door latch assembly can cost a similar amount in parts. If the control board is ultimately found to be at fault, repair costs will be higher, generally ranging from $150 to $350 or more for parts and labor combined.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass