mypros+
Error code reference

Electrolux Dryer Error Code 35

Capacitive sensor assembly communication problem with main control board (500 and 600 series only).

Electrolux codesElectrolux dryer codes

Capacitive sensor assembly communication problem with main control board (500 and 600 series only).

First step from the service manual

Check wiring between main control board and capacitive sensor assembly. 1. If wiring is good, replace capacitive sensor assembly. 2. If problem is not corrected, replace main control board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 35.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 35 means on a Electrolux dryer

Error code 35 on Electrolux 500 and 600 series dryers indicates a communication failure between the capacitive sensor assembly and the main control board. The capacitive sensor assembly is responsible for detecting moisture levels in the drum by measuring the electrical capacitance of fabrics as they tumble past the sensor bars. When the main control board loses the ability to send or receive data from this assembly, it throws error code 35 and may interrupt or prevent normal drying cycles from completing.

The most common trigger for this fault is a wiring issue between the two components. Connectors can loosen over time due to vibration, and individual wires in the harness can develop breaks or shorts that disrupt the communication signal. Corrosion at connector terminals is another frequent culprit, particularly in humid laundry environments. A thorough inspection of the wiring harness, including checking each connector for secure seating and visible damage, is the required first diagnostic step before replacing any components.

If the wiring and connectors check out as intact and properly connected, the capacitive sensor assembly itself is the next suspect and should be replaced first. Only if replacing the sensor assembly does not resolve the fault should the main control board be considered as the defective component. Because this error code is specific to the 500 and 600 series platform, technicians working on other Electrolux dryer lines should verify model compatibility before applying this diagnostic path.

Source: manufacturer service documentation.

Common causes of 35

  1. 01

    Loose or disconnected wiring harness connector

    Wiring / connection

    Vibration from normal dryer operation can loosen the connectors between the capacitive sensor assembly and the main control board. Inspect all connectors along the harness for secure seating and re-seat any that appear loose.

  2. 02

    Damaged or broken wiring in the harness

    Part replacement

    Individual wires in the harness can develop breaks, frays, or shorts that prevent communication signals from passing through. Visually inspect the full length of the harness and use a multimeter to test for continuity on each wire.

  3. 03

    Corroded connector terminals

    Wiring / connection

    Moisture in a laundry room environment can cause corrosion to build up on the metal terminals inside connectors, increasing resistance and degrading the communication signal. Look for green or white discoloration on terminals and clean or replace affected connectors.

  4. 04

    Faulty capacitive sensor assembly

    Part replacement

    The capacitive sensor assembly itself can fail internally, causing it to stop communicating with the main control board even when wiring is intact. If the wiring checks out as good, replacing the capacitive sensor assembly is the next recommended step.

  5. 05

    Failed main control board

    Part replacement

    If replacing the capacitive sensor assembly does not clear the error, the main control board may have lost its ability to communicate with the sensor. This is the least likely cause and should only be addressed after the sensor assembly has been replaced and tested.

See the test procedure for each cause

Frequently asked questions about 35

What does 35 mean on a Electrolux dryer?
Error code 35 on Electrolux 500 and 600 series dryers signals a communication problem between the capacitive sensor assembly and the main control board. The capacitive sensor monitors moisture levels in the drum during drying. When the control board cannot communicate with this sensor, it logs error 35 and may interrupt the drying cycle.
Can I fix error code 35 on my Electrolux dryer myself?
A knowledgeable DIYer can start by inspecting the wiring harness and connectors between the capacitive sensor assembly and the main control board for loose connections, visible damage, or corrosion. If the wiring appears fine, replacing the capacitive sensor assembly is the next step. Replacing the main control board is the final step if the sensor swap does not resolve the fault, and that repair is more involved and may be better left to a technician.
Is it safe to keep using my dryer when error code 35 appears?
Continuing to use the dryer with error code 35 active may result in improper moisture sensing, meaning clothes could come out still damp or the dryer may not complete cycles normally. The error does not indicate an immediate fire or electrical safety hazard, but running the dryer in a degraded sensing state can lead to extended cycle times and increased energy use. It is best to diagnose and resolve the issue before relying on the dryer for regular use.
How much does it cost to repair error code 35 on an Electrolux dryer?
If the fix is simply re-seating a loose connector, the repair costs nothing beyond your time. A replacement capacitive sensor assembly typically runs in the range of $30 to $80 in parts. If the main control board also needs to be replaced, parts alone can range from $100 to $250 or more, and adding professional labor will increase the total cost significantly.
Will resetting my Electrolux dryer clear error code 35?
A reset may temporarily clear the error code from the display, but if the underlying wiring fault or component failure is still present, the code will return once the dryer attempts to communicate with the capacitive sensor assembly again. A reset is not a repair. The wiring, connectors, and components need to be inspected and corrected to permanently resolve the fault.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass