mypros+
Error code reference

Electrolux Range Error Code Convection Bake + Broil + Lock (LEDs 2,4,6)

Maximum lock attempts exceeded on motor door latch.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Convection Bake + Broil + Lock (LEDs 2,4,6) error code actually means

Your oven tried to lock its door for a self-cleaning cycle but was not able to complete the lock after several attempts. This usually means the door latch motor or its sensors are not working correctly. The oven is preventing the clean cycle from running until this issue is resolved.

Diagnostic procedure

The full Convection Bake + Broil + Lock (LEDs 2,4,6) procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Set the oven up for a clean cycle. Check if the latch motor turns. If no, check voltage applied to latch motor. If line to neutral, replace latch mechanism. If zero, replace electronic control board. Check phase and lock switches.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Convection Bake + Broil + Lock (LEDs 2,4,6) procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of Convection Bake + Broil + Lock (LEDs 2,4,6)

Ranked by how often they cause this code
  1. 1Failed latch motor
  2. 2Faulty lock or phase switch
  3. 3Failed electronic control board
  4. 4Latch mechanism obstruction or misalignment

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Convection Bake + Broil + Lock (LEDs 2,4,6)

What does Convection Bake + Broil + Lock (LEDs 2,4,6) mean on a Electrolux range?
This LED combination indicates that the oven's door latch motor has exceeded the maximum number of allowed locking attempts without successfully securing the door. The fault is triggered during or before a self-cleaning cycle when the control board cannot confirm that the latch has engaged. It typically points to a problem with the latch motor, the lock or phase switch, or the electronic control board.
Is it safe to use the oven while this error is active?
Normal baking and broiling functions may still operate, but the self-cleaning cycle cannot safely run while this fault is present because the door cannot be confirmed as locked. It is best to avoid initiating a clean cycle until the latch issue is diagnosed and repaired. Continuing to attempt clean cycles with a faulty latch could cause additional faults or damage to the control board.
How much does it cost to repair this error on an Electrolux range?
Repair costs vary depending on which component has failed. A replacement latch mechanism assembly typically runs in the range of $50 to $150 for the part, while a replacement electronic control board can range from $150 to $350 or more. Adding professional labor costs generally brings the total repair into the $200 to $500 range, depending on your location and the specific parts required.
Can I fix this error myself or do I need a technician?
A knowledgeable DIYer can perform the basic voltage test at the latch motor by setting the oven up for a clean cycle and checking whether line-to-neutral voltage is present. If voltage is present but the motor does not turn, the latch mechanism needs replacement. If no voltage is present, the control board requires replacement. Both repairs involve working near live voltage, so comfort with electrical safety procedures is essential before attempting them.
Will resetting the oven clear this error code?
Cycling power to the range may temporarily clear the displayed fault, but the error will return as soon as the oven attempts another clean cycle and the latch motor again fails to confirm a locked position. The underlying mechanical or electrical fault in the latch system must be repaired for the error to be permanently resolved.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass