mypros+
Error code reference

Electrolux Range Error Code F003

The oven user interface board is incorrectly configured.

Electrolux codesElectrolux range codes

The oven user interface board is incorrectly configured.

First step from the service manual

Turn range OFF, unplug power cord from wall, wait 30 seconds and reapply power. If problem persists, replace oven user interface.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F003.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F003 means on a Electrolux range

The F003 error code on an Electrolux range indicates that the oven user interface board has been detected as incorrectly configured. The user interface board is the control panel assembly responsible for accepting input commands, displaying operational status, and communicating cooking parameters to the main control board. When the system detects a configuration mismatch or an initialization failure within this board, it triggers the F003 fault to prevent unsafe or erratic oven operation.

This error typically arises from a software or firmware configuration issue within the user interface board itself, though it can also result from a temporary communication fault caused by a power surge or transient voltage event. Because the board stores configuration data that must match the appliance's specific model parameters, any corruption of that data or an improperly matched replacement board can produce this fault.

The recommended first diagnostic step is a hard reset: power off the range, unplug the power cord from the wall outlet, wait a minimum of 30 seconds to allow capacitors to fully discharge and memory to clear, then reapply power. If the F003 code returns after this reset, the user interface board has a persistent configuration fault and will need to be replaced. A reset alone resolves this error in cases where a transient event caused the initial fault, but a recurring code confirms a hardware or firmware failure in the board itself.

Source: manufacturer service documentation.

Common causes of F003

  1. 01

    Transient power surge or voltage spike

    Wiring / connection

    A brief power surge can corrupt the configuration data stored on the user interface board, triggering F003. A 30-second hard reset after unplugging the range will clear this if a transient event was the cause.

  2. 02

    Failed or corrupted user interface board

    Part replacement

    If the internal firmware or configuration memory on the user interface board has permanently failed, the board cannot initialize correctly and will continue to display F003 after every reset. Replacement of the board is required.

  3. 03

    Incorrect replacement board installed

    Part replacement

    If a user interface board was previously replaced with a part that does not match the model's required configuration, the system will detect the mismatch and trigger F003. Verifying that the installed board matches the exact model requirements is necessary.

  4. 04

    Intermittent power supply to the board

    Wiring / connection

    Loose wiring connections or a damaged harness supplying power to the user interface board can cause intermittent initialization failures that present as F003. Inspecting the connector pins and wiring between the board and the main control for damage or looseness can help identify this cause.

See the test procedure for each cause

Frequently asked questions about F003

What does F003 mean on a Electrolux range?
F003 indicates that the oven user interface board is incorrectly configured. The control system has detected that the interface board did not initialize properly or that its configuration data does not match expected parameters. This fault prevents normal operation to avoid erratic or unsafe behavior. A hard reset is the first step, and persistent faults require board replacement.
Will resetting my Electrolux range clear the F003 error?
A reset will clear F003 if the cause was a temporary power surge or transient voltage event. To reset, turn the range off, unplug the power cord from the wall outlet, wait at least 30 seconds, and then restore power. If the code reappears after this process, the user interface board has a persistent fault and a reset will not resolve it.
Is it safe to use my Electrolux range while F003 is displayed?
An F003 fault indicates the control panel is not functioning correctly, which means the oven may not respond to commands reliably. It is best to avoid using the range until the fault is resolved. Continuing to operate an appliance with a confirmed control board fault could result in unpredictable behavior.
How much does it cost to fix the F003 error on an Electrolux range?
If the error clears with a hard reset, there is no parts cost involved. If the user interface board requires replacement, parts costs typically range from around $100 to $300 or more depending on the specific model, with additional labor costs if a technician performs the repair. Obtaining a quote from a service provider for your specific model will give you a more accurate estimate.
Can I replace the Electrolux oven user interface board myself?
Replacing the user interface board is a task that a knowledgeable DIYer can often complete, as it generally involves disconnecting wiring harnesses and swapping the board. However, it is important to confirm the replacement part matches your exact model to avoid triggering F003 again due to a configuration mismatch. If you are not comfortable working with appliance electronics, hiring a qualified technician is the safer option.

Related Electrolux range codes

All Electrolux range codes
View all 175 Electrolux range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass