mypros+
Error code reference

Electrolux Range Error Code Bake + Convection Bake + Convection Roast + Broil + Clean (LEDs 1,2,3,4,5)

Inter-processor communications failure on motor door latch.

Electrolux codesElectrolux range codes

Inter-processor communications failure on motor door latch.

First step from the service manual

Replace electronic control board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for Bake + Convection Bake + Convection Roast + Broil + Clean (LEDs 1,2,3,4,5).

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What Bake + Convection Bake + Convection Roast + Broil + Clean (LEDs 1,2,3,4,5) means on a Electrolux range

When an Electrolux range illuminates the Bake, Convection Bake, Convection Roast, Broil, and Clean LEDs simultaneously (indicators 1 through 5), the control system is signaling an inter-processor communications failure specifically related to the motor door latch circuit. This error reflects a breakdown in the communication pathway between the main electronic control board and the secondary processor responsible for monitoring and controlling the motorized oven door latch, which is a critical component in self-cleaning cycle safety.

The motorized door latch system uses a dedicated motor and position sensors to lock the oven door during high-temperature clean cycles and to confirm latch position to the control board. The inter-processor communication link transmits status data between the two control modules. When this data exchange fails, drops out, or returns an unexpected response, the control logic triggers this multi-LED fault pattern to alert the technician that the communication protocol has broken down rather than that a simple sensor or motor has failed.

The most likely root cause is a failure within the main electronic control board itself, which is why the primary diagnostic step is board replacement. However, wiring harness integrity between the control board and the latch motor assembly should also be evaluated. Damaged connectors, corroded pins, or broken wires in the latch motor harness can interrupt the communication signal and produce this same fault code before a board replacement is carried out.

Source: manufacturer service documentation.

Common causes of Bake + Convection Bake + Convection Roast + Broil + Clean (LEDs 1,2,3,4,5)

  1. 01

    Failed electronic control board

    Part replacement

    The main electronic control board is the primary suspect when this fault appears. An internal failure in the board's communication circuitry prevents it from exchanging data with the latch motor processor, and board replacement is the first recommended diagnostic step.

  2. 02

    Damaged wiring harness to door latch motor

    Wiring / connection

    The wiring harness connecting the control board to the motorized door latch assembly can develop broken wires, loose connectors, or corroded pins that disrupt the communication signal. Inspect the harness and connectors for visible damage, corrosion, or loose seating before condemning the board.

  3. 03

    Faulty door latch motor assembly

    Part replacement

    The motorized latch unit itself contains components that communicate status back to the control board. A failed motor or internal latch circuit can prevent proper communication handshake, triggering this fault code.

  4. 04

    Loose or disconnected control board connector

    Wiring / connection

    Vibration or thermal cycling can cause the harness connector at the control board to work loose over time, interrupting the communication link. Check that all connectors at the board are fully seated and locked.

See the test procedure for each cause

Frequently asked questions about Bake + Convection Bake + Convection Roast + Broil + Clean (LEDs 1,2,3,4,5)

What does Bake + Convection Bake + Convection Roast + Broil + Clean (LEDs 1,2,3,4,5) mean on a Electrolux range?
This combination of five illuminated LEDs indicates an inter-processor communications failure on the motor door latch system. The main electronic control board has lost communication with the processor responsible for the motorized oven door latch. This fault is not a simple sensor error but a breakdown in the internal communication pathway between two control modules. A technician should inspect the wiring harness and connections before replacing the main control board.
Can I fix this error myself, or do I need a technician?
The primary diagnostic step for this fault is replacing the electronic control board, which involves working inside the range's control panel area and handling electrical components. While a knowledgeable DIYer can inspect the wiring harness and connectors for obvious damage, the board replacement itself is best handled by a qualified appliance technician. Attempting repairs without proper knowledge of the electrical system carries a risk of injury or further damage to the range.
Is it safe to use my Electrolux range while this error is displayed?
Because this fault involves the motorized door latch system, which is a safety-critical component for self-cleaning cycles, it is not advisable to run a self-clean cycle until the fault is resolved. The door latch is responsible for keeping the oven sealed at high temperatures during cleaning. Standard baking or cooking functions may or may not be available depending on how the control board responds to the fault, but the underlying communication failure should be addressed promptly.
Will resetting the range clear this error code?
A power reset by unplugging the range or switching off the circuit breaker for several minutes may temporarily clear the fault display. However, if the underlying cause is a failed control board or damaged wiring, the error will return once power is restored and the system attempts to communicate with the latch motor processor again. A reset alone is not a repair and should not be relied on as a solution.
How much does it cost to repair this error on an Electrolux range?
Repair costs depend on whether the issue is a wiring problem or a full control board replacement. Wiring harness repairs or connector fixes are generally less expensive, typically falling in the range of $75 to $150 in labor if no parts are needed. A replacement electronic control board for an Electrolux range can cost anywhere from $150 to $350 or more for the part alone, with total repair costs including labor often ranging from $250 to $500 depending on the technician and region.

Related Electrolux range codes

All Electrolux range codes
View all 175 Electrolux range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass