mypros+
Error code reference

Electrolux Range Error Code 55

Inductor temperature sensor break (Right Front).

Electrolux codesElectrolux range codes

Inductor temperature sensor break (Right Front).

First step from the service manual

Verify element temperature sensor is correctly connected to the Induction Housing Assembly connector. Replace inductor if temperature sensor resistor value is not approximately 1000 ohms (blue wires) at room temperature.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 55.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 55 means on a Electrolux range

Error code 55 on an Electrolux induction range indicates a break or open circuit in the temperature sensor associated with the right front inductor. This sensor is a negative temperature coefficient (NTC) thermistor embedded in or connected to the induction housing assembly. At room temperature, a properly functioning sensor should read approximately 1000 ohms across its blue wires. An open circuit, damaged wiring, or a failed thermistor will prevent the control board from receiving valid temperature data, triggering this fault and disabling the affected burner zone as a safety measure.

The inductor temperature sensor plays a critical role in protecting the induction coil and surrounding components from thermal overload. The control system continuously monitors the resistance value from this thermistor to regulate power output and prevent unsafe operating temperatures. When the sensor circuit is broken, whether from a disconnected harness, damaged wires, or a failed sensor element, the control board interprets the open circuit as a fault condition and shuts down that heating zone.

Diagnosis begins at the connector where the sensor plugs into the induction housing assembly. A loose or unseated connector is the most straightforward cause and should be checked before testing component resistance. If the connector is secure, use a multimeter to measure resistance across the blue sensor wires. A reading that deviates significantly from 1000 ohms at room temperature, or an open-circuit reading, confirms the thermistor has failed and the inductor assembly will need to be replaced.

Source: manufacturer service documentation.

Common causes of 55

  1. 01

    Disconnected sensor connector

    Wiring / connection

    The temperature sensor harness connector may have come loose from the induction housing assembly. This is the first thing to check, as reseating the connector can resolve the fault without replacing any parts.

  2. 02

    Failed inductor temperature sensor (thermistor)

    Part replacement

    The NTC thermistor itself may have failed internally, resulting in an open circuit. Measuring across the blue sensor wires at room temperature will show a reading far outside the expected 1000 ohms, or no continuity at all, confirming the inductor assembly needs replacement.

  3. 03

    Damaged sensor wiring

    Part replacement

    The blue sensor wires running between the thermistor and the connector may be broken, pinched, or burned. Visually inspect the wire routing for any damage, and use a multimeter to check for continuity along the length of each wire.

  4. 04

    Corroded or damaged connector terminals

    Wiring / connection

    Even if the connector is physically seated, corroded or bent terminals can interrupt the circuit. Inspect the connector pins closely for oxidation, heat damage, or deformation that could cause a high-resistance or open connection.

  5. 05

    Faulty control board

    Part replacement

    In rare cases, the control board may misread or fail to process the sensor signal even when the sensor and wiring test correctly. This is the least likely cause and should only be considered after the sensor and harness have been confirmed good.

See the test procedure for each cause

Frequently asked questions about 55

What does 55 mean on a Electrolux range?
Error code 55 means the control board has detected a break in the temperature sensor circuit for the right front induction burner. The sensor, a thermistor that should measure approximately 1000 ohms at room temperature, is either disconnected or has failed. The range disables the affected burner zone until the fault is resolved. This is a safety feature to prevent uncontrolled heating due to missing temperature feedback.
Can I fix error code 55 myself?
A homeowner comfortable with basic appliance work can check whether the sensor connector is simply loose or unseated at the induction housing assembly. If reseating the connector clears the code, no parts are needed. If the connector is secure but the fault remains, testing and replacing the inductor assembly requires disassembling the cooktop and working with internal components, which is generally best handled by a qualified technician.
Is it safe to keep using my range when error code 55 appears?
The right front burner zone will be disabled when error code 55 is active, so you cannot use that specific cooking area. The remaining burner zones may continue to function normally. It is safe to use the other zones, but the range should be repaired before relying on the right front burner again, as the temperature sensor is a key safety component for that zone.
Will resetting the range clear error code 55?
Power cycling the range may temporarily clear the display, but code 55 will return as soon as the control board checks the right front sensor circuit again and detects the open circuit. A reset does not fix the underlying issue. The sensor connector, wiring, or inductor assembly must be inspected and repaired for the fault to be permanently resolved.
How much does it cost to repair error code 55 on an Electrolux range?
If only the connector needs to be reseated, there is no parts cost and minimal labor. If the inductor assembly requires replacement, parts alone typically range from around 150 to 400 dollars depending on the specific model, with additional labor charges if a technician is hired. Wiring repairs generally fall somewhere in between depending on the extent of the damage.

Related Electrolux range codes

All Electrolux range codes
View all 175 Electrolux range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass