mypros+
Error code reference

Electrolux Range Error Code E39

Configuration mismatch between the UIB and the filter board (can occur when a filter board is replaced).

Electrolux codesElectrolux range codes

Configuration mismatch between the UIB and the filter board (can occur when a filter board is replaced).

First step from the service manual

Make sure the UIB is connected correctly.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E39.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E39 means on a Electrolux range

Error code E39 on an Electrolux range indicates a configuration mismatch between the User Interface Board (UIB) and the filter board. These two boards communicate during startup to verify that their firmware or hardware configurations are compatible. When the range detects that these two components do not agree on their configuration parameters, it throws E39 to prevent potentially unsafe or erratic operation.

This error most commonly surfaces after a filter board replacement. When a new filter board is installed, its stored configuration data may not match what the UIB expects. In some cases, the boards may need to be paired or the UIB may need to relearn the configuration of the new filter board. The issue can also arise from a loose or improperly seated wiring harness connection between the two boards, which causes intermittent or failed communication rather than a true hardware incompatibility.

The first diagnostic step is to confirm that the UIB is connected correctly and that all harness connectors are fully seated. If connections are secure and the error persists, the filter board or UIB may need to be replaced or reconfigured to resolve the mismatch. Because this error directly involves control board communication, it should be diagnosed carefully before ordering replacement parts.

Source: manufacturer service documentation.

Common causes of E39

  1. 01

    Recently replaced filter board

    Wiring / connection

    Replacing the filter board is the most common trigger for E39. The new board may carry a different firmware version or configuration profile that the UIB does not recognize, causing a mismatch at startup.

  2. 02

    Loose or improperly connected wiring harness

    Wiring / connection

    If the harness connecting the UIB to the filter board is not fully seated or has backed out of its connector, the boards cannot communicate reliably and E39 will be triggered. Inspect all connectors between the two boards for firm seating.

  3. 03

    Incompatible replacement filter board

    Part replacement

    If a filter board that does not match the original part specification was installed, the UIB may be unable to establish a valid configuration handshake. Verifying that the replacement board is the correct part for the specific model is essential.

  4. 04

    Faulty UIB

    Part replacement

    A UIB that has failed or has corrupted configuration data may be unable to properly recognize even a compatible filter board. If connections are correct and the filter board is confirmed to be correct, the UIB itself may need to be replaced.

  5. 05

    Faulty filter board

    Part replacement

    In cases where no recent repair has been performed, a filter board that has developed an internal fault may begin reporting an incompatible configuration to the UIB, triggering E39 without any physical changes to the appliance.

See the test procedure for each cause

Frequently asked questions about E39

What does E39 mean on a Electrolux range?
E39 means the range has detected a configuration mismatch between the User Interface Board (UIB) and the filter board. These two control boards exchange configuration data during startup, and when they do not match, the range generates this error code. It is most frequently seen after a filter board replacement but can also result from a loose wiring connection between the two boards.
Can I fix E39 on my Electrolux range myself?
The first step you can take yourself is checking that all wiring harness connections between the UIB and filter board are fully and firmly seated. If the error appeared after a recent filter board replacement, confirm that the correct replacement part was used. Beyond inspecting connections, resolving a true configuration mismatch or replacing a faulty board typically requires a qualified technician.
Will resetting the range clear the E39 error code?
A power reset by unplugging the range or shutting off the circuit breaker for a few minutes may temporarily clear the error, but it will return if the underlying cause is not addressed. If there is a genuine configuration mismatch or a hardware incompatibility between the UIB and filter board, the error will reappear on the next startup.
Is it safe to use my Electrolux range while E39 is displayed?
It is not advisable to continue using the range while E39 is active. The error indicates that two critical control boards are not communicating correctly, which could result in unpredictable behavior from the control system. The range should be diagnosed and repaired before being returned to normal use.
How much does it cost to repair an E39 error on an Electrolux range?
Repair costs vary depending on which component needs to be replaced. A service call and diagnostic visit alone can range from $75 to $150. If a filter board or UIB replacement is needed, parts can range from $100 to $300 or more depending on the model, with total repair costs including labor typically falling between $200 and $500.

Related Electrolux range codes

All Electrolux range codes
View all 175 Electrolux range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass