mypros+
Model reference

Frigidaire 763

Dishwasher

10 documents92 error codes14 service modes

Available documentation

Service Manual

  • 24-INCH BUILT-IN DISHWASHER Service Data Sheet14 pg
    Covers this model
  • Use & Care Guide - Built-In Dishwasher72 pg
    Covers this model

Wiring Diagram

  • Wiring Diagram2 pg
    Covers this model
  • Wiring Diagram1 pg
    Covers this model

Tech Tip

  • Tech Tip LNTT2512 Noise Concern1 pg
    Covers this model

Other

  • A05763001Afr32 pg
    Covers this model
  • 808936658.pdf2 pg
    Covers this model
  • 599567326512 pg
    Covers this model
  • 599572379714 pg
    Covers this model

Tech Data Sheet

  • Tech Data Sheet1 pg
    Covers this model
MyPros+ Max

Diagnose your Frigidaire 763.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (92)

CodeMeaning
ASAmbient thermistor sensor located in the remote control has failed.CFCheck FoodCLEAn dELAyControl requires a waiting period before another self-clean cycle can be…door LocOven door is in the process of locking or is locked.door OPnOven door has finished unlocking and may be opened after self-clean cycle…E11Shorted keypad (ESEC system).E14ESEC key read ribbon cable is disconnected or defective.E21Communication failure between the filter board and UIB.E30Synchronization failureE31Synchronization failureE32Power supply defectE33Power supply defectE34Internal communication failureE35AC Input voltage too high.E36Communication error (left cooking zones).E37Heat sink temp sensor break (left cooking zones).E39Configuration mismatch between the UIB and the filter board (can occur when a…E51Surface unit temp sensor breakE52Surface unit temp sensor breakE54Surface unit temp sensor breakE55Surface unit temp sensor breakE61Surface unit sensor too hotE62Surface unit sensor too hotE64Surface unit sensor too hotE65Surface unit sensor too hotE70Synchronization failureE71Synchronization failureE72Power supply defectE73Power supply defectE74Internal communication failure
View all 92 error codes
E75AC Input voltage too high.E76Communication error (right cooking zones).E77Heat sink temp sensor break (right cooking zones).Er 01Leak DetectorEr 02Thermistor/turbidity module has failed.Er 03Wash pump is not operating.Er 04Drying damper is not operating.Er 05During the dry cycle, the control board does not receive proper speed feedback…Er 06During the dry cycle, the control board does not receive proper speed feedback…Er 07During drain mode, the control board does not receive proper position feedback…Er 08Control board has verified a tactile or touch switch on the user interface is…Er 09Communication failure between main user board and power supply.Er 10Failure in the mains power relay.Er 11Drain valveEr 12Drain valve is running when it should be off.Er 13System wideERRORSensor did not detect steam properly during sensor cooking or reheating; steam…ESEvaporator thermistor sensor has failed.FThe oven control system has detected a fault or anomaly; an F error code with a…F__Oven control has detected a fault or error condition (F followed by a number).F10Control has sensed a potential runaway oven condition; control may have a…F11Shorted key detectedF12EOC internal software error or failure.F13Control's internal checksum may have become corrupted.F14Relay watchdog failure.F15Controller self check failed.F16EOC internal software error or failure.F17EOC internal software error or failure.F18EOC internal software error or failure.F19EOC internal hardware error or failure.F20Bad communication between display board and relay board.F23Communication failure between VSC board and EOC (upper or main oven).F24Communication failure between VSC board and EOC (lower oven if so equipped).F25Communication failure between VSC board and EOC.F26Communication failure with Mini Oven Control Board (for models equipped with…F30Open RTD sensor probe or wiring problemF31Shorted RTD sensor probe or wiring problemF32Key loop is detected as an open circuit.F40Cooktop lockout error (some models).F42EOC internal software configuration error.F60EOC oven temperatureF62Internal signal voltage error.F63Display communication error.F64Time base failureF65Keyboard short circuit or internal EOC failure.F66EOC internal power supply failure.F68High voltage conditionF69High voltage conditionF8The oven door was left open while controls were set for the self-cleaning cycle.F90Door motor mechanism failure.F91Door lock motor or latch circuit failure.F92Door lock motor or latch circuit failure.F93Door lock motor or latch circuit failure.F94Door lock motor or latch circuit failure.F95Door motor mechanism failure.HotOven is still hot after self-clean cycleHSHeat thermistor sensor has failed (heat capable models only).LinE ERREOC internal voltage test error or failure.PFPower failure detected; the display flashes 'PF' when the range is first…Prob ERRProbe errorProb Too HotThe probe sensor temperature has exceeded 250°F (121°C)SFSabbath failure

Service modes (14)

  • Child LockPress and hold the AIR DRY touchpad for 3 seconds to lock controls.
  • child_lockPress the user pref pad, then number 1, then press the START enter +30 sec pad.
  • Continuous bake setting (override 12-Hour Energy Saving)["1. Press and hold Timer On/Off down for 6 seconds until a tone sounds.","2. '—
  • demonstrationPress the user pref pad, number 5, 0, then press and hold the START enter +30 sec pad for three…
  • Demonstration Mode["Touch SET CLOCK","Touch the number 0","Touch and hold START for three seconds","DEMO ON will…
  • ESEC Configuration Reset (Error 39)Press and hold both the right front and right rear ON/OFF keys until the ESEC displays change to…
  • Initial Setup / Normal Operating Mode ResetPress and hold the Sanitize touchpad for 8 seconds.
  • Lockout feature["1
  • Oven temperature calibration1
  • Oven temperature calibration adjustment["1
  • Silent control panel["1
  • Temperature Adjustment (Calibration Offset)1
  • Temperature Calibration Adjustment1
  • Temperature display change (°F or °C)["1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Frigidaire dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax