mypros+
Error code reference

Fisher & Paykel Oven Error Code F0.00

Pyrolytic cycle has been stopped and restarted when it was quite a way through; displayed after about 10…

Fisher & Paykel codesFisher & Paykel oven codes

Pyrolytic cycle has been stopped and restarted when it was quite a way through; displayed after about 10 minutes and the pyrolytic cycle is zeroed (shown with AUTO flashing).

First step from the service manual

Put the switch to 0, wait for at least 15 minutes, then repeat the operations to start the pyrolytic cycle. If message persists after several attempts, contact the After-Sales Service Centre.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F0.00.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F0.00 means on a Fisher & Paykel oven

The F0.00 error code on a Fisher & Paykel oven is triggered when a pyrolytic self-cleaning cycle has been interrupted and then restarted after significant progress had already been made. The oven's control system monitors the state of the pyrolytic cycle and detects when the cycle is stopped and then re-initiated mid-process. After approximately 10 minutes following the restart attempt, the controller displays F0.00 and zeroes out the pyrolytic cycle entirely, indicated by the AUTO indicator flashing on the display panel.

The pyrolytic cleaning process involves heating the oven cavity to extremely high temperatures, typically above 400 degrees Celsius, to incinerate food residue and grease. The control system manages this process as a continuous sequence, and interrupting it partway through disrupts the thermal and timing logic. When the cycle is restarted without a proper cooldown and reset period, the controller cannot safely resume from the interrupted point and instead flags the condition with F0.00 to prevent unsafe operation.

Resolving this error does not typically involve faulty components. The correct procedure is to turn the oven selector switch to the 0 position, allow a minimum of 15 minutes for the oven to cool and the control system to fully reset, and then restart the pyrolytic cycle from the beginning. If the error persists after several proper restart attempts, an underlying fault in the control electronics or cycle management logic may be present, requiring professional diagnosis.

Source: manufacturer service documentation.

Common causes of F0.00

  1. 01

    Pyrolytic cycle interrupted mid-process

    Wiring / connection

    The most frequent trigger for F0.00 is the user stopping the pyrolytic cycle after it has progressed significantly, then attempting to restart it without allowing adequate cooldown time. The control system cannot resume a partial cycle and resets instead.

  2. 02

    Insufficient cooldown before restart

    Wiring / connection

    Restarting the pyrolytic cycle too quickly after stopping it prevents the control system from fully resetting its internal state. A minimum of 15 minutes with the selector at 0 is required before attempting a new cycle.

  3. 03

    Accidental cycle cancellation

    Wiring / connection

    An unintentional press of the cancel or power button during the cleaning cycle can trigger this sequence of events. Reviewing the sequence of control inputs before the error appeared can help confirm this cause.

  4. 04

    Power interruption during the pyrolytic cycle

    Wiring / connection

    A brief power outage or fluctuation that cuts power to the oven mid-cycle can cause the controller to register a stopped cycle, leading to F0.00 when power is restored and operation is resumed.

  5. 05

    Fault in the oven control board

    Part replacement

    If the error persists after multiple correct restart attempts with proper cooldown periods, the cycle management logic on the main control board may be malfunctioning. This scenario requires professional service assessment.

See the test procedure for each cause

Frequently asked questions about F0.00

What does F0.00 mean on a Fisher & Paykel oven?
F0.00 indicates that the pyrolytic self-cleaning cycle was stopped and then restarted after it had already progressed significantly through the cleaning sequence. The oven displays this code approximately 10 minutes after the failed restart attempt and cancels the cycle entirely, shown by the AUTO indicator flashing. This is a control system response to an interrupted cycle, not an indication of a broken component in most cases. Turning the oven off, waiting at least 15 minutes, and restarting the cycle from the beginning will typically resolve it.
How do I fix the F0.00 error on my Fisher & Paykel oven?
Turn the oven selector switch to the 0 position and wait a minimum of 15 minutes before doing anything else. This allows the oven to cool and the control system to fully reset. After the wait, restart the pyrolytic cleaning cycle from the beginning following the standard procedure. If the error reappears after several correct restart attempts, contact a qualified service technician as there may be an underlying fault in the control electronics.
Is the F0.00 error on a Fisher & Paykel oven a safety concern?
The F0.00 code itself is not a symptom of a dangerous fault. It is a protective response by the oven's control system when it detects that a pyrolytic cycle cannot be safely resumed from an interrupted state. The oven cancels the cycle to avoid operating outside its designed sequence. Following the correct reset and restart procedure is all that is typically needed to safely use the pyrolytic function again.
Will resetting the oven clear the F0.00 error code?
Yes, in most cases a proper reset will clear the F0.00 error. The reset requires turning the selector switch to 0 and waiting at least 15 minutes, not just a brief power cycle. After this period, the control system should be ready to accept a new pyrolytic cycle start command. If the code returns immediately or after several proper reset attempts, a deeper fault in the control board may be present and professional service is recommended.
How much does it cost to repair a Fisher & Paykel oven showing F0.00?
In the majority of F0.00 cases no repair cost is involved, since the error is resolved simply by waiting 15 minutes and restarting the pyrolytic cycle. If the error persists and a technician determines the main control board has failed, replacement part and labor costs can range from $200 to $600 or more depending on the specific model and your location. Getting a diagnostic assessment from an authorized service center before committing to parts is always advisable.

Related Fisher & Paykel oven codes

All Fisher & Paykel oven codes
View all 17 Fisher & Paykel oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass