mypros+
Error code reference

Haier Washer Error Code End

A program has ended.

Haier codesHaier washer codes

A program has ended.

MyPros+ Max

Get the full diagnostic procedure for End.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What End means on a Haier washer

The "End" display on a Haier washer is not an error code in the traditional sense. It is a status notification indicating that the selected wash program has completed all of its cycles, including wash, rinse, and spin phases. The control board advances through each programmed stage, and once the final stage concludes, the display switches to "End" to inform the user that the machine has finished its operation and laundry is ready to be removed.

This message is part of normal washer behavior and does not indicate a fault with any component. The control board monitors cycle progression through its internal timer and sensor inputs, and the "End" notification is triggered when all programmed routines have been executed successfully. No diagnostic action is required when this message appears under normal circumstances.

In some cases, the "End" message may persist on the display until the door is opened or the washer is powered off. If the display shows "End" but the cycle does not appear to have completed correctly, such as clothes remaining soaking wet or the drum still containing water, that situation would warrant further investigation into the drain pump, lid or door latch, or cycle selection. Otherwise, seeing "End" simply means the machine performed as intended.

Source: manufacturer service documentation.

Common causes of End

  1. 01

    Normal cycle completion

    Wiring / connection

    The washer has successfully completed all stages of the selected wash program. No action is needed beyond unloading the laundry.

  2. 02

    Display persisting after cycle ends

    Wiring / connection

    Some Haier models hold the "End" message on the display until the door is opened or the unit is powered off. This is expected behavior and clears on its own once the machine is reset or restarted.

  3. 03

    Child lock or delayed start interaction

    Wiring / connection

    If a delayed start or child lock feature was active during the cycle, the "End" message may appear and remain visible longer than expected. Disabling these features through the control panel will allow normal operation to resume.

  4. 04

    Incomplete cycle with standing water present

    Wiring / connection

    If "End" appears but water remains in the drum, the drain pump or drain hose may have an issue that prevented full drainage. Check the drain filter and hose for clogs before the next cycle.

See the test procedure for each cause

Frequently asked questions about End

What does End mean on a Haier washer?
"End" on a Haier washer means the selected wash program has finished running through all of its stages, including wash, rinse, and spin. It is a status notification, not an error or fault code. Your laundry is ready to be removed from the drum.
Do I need to do anything to fix the End message on my Haier washer?
No fixing is required. The "End" message is a normal indication that the cycle is complete. Simply open the door and remove your laundry. If the message does not clear, power the machine off and back on to reset the display.
Is it safe to leave laundry in the washer after End appears?
It is safe in terms of the appliance itself, but leaving wet laundry sitting in a closed drum for an extended period can lead to mildew or odors on the clothing and inside the drum. It is best to remove laundry promptly once the "End" notification appears.
Will resetting the washer clear the End message?
Yes. Powering the washer off and then back on will clear the "End" message from the display. You can also clear it simply by opening the door on most Haier models. No special reset procedure is needed.
How much does it cost to repair a Haier washer if End appears along with other problems?
If "End" appears alongside actual symptoms like standing water or wet clothes, the underlying issue may involve a clogged drain filter, a drain pump, or a door latch component. Drain pump replacements typically range from $75 to $200 depending on parts and labor costs in your area. A clogged drain filter can usually be cleared at no cost with basic tools.

Related Haier washer codes

All Haier washer codes
View all 66 Haier washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass