Skip to main content
Error code reference
Haier Washer Error Codes
67 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
CLChild lock is activated; all buttons are locked and will not function.DoorDoor is not properly shut 20 seconds after program is started.DrainageDrainage error, water not emptied within 4 minutes.E0Waterfall current is poor or out during pre-wash, causing the washer to stop running.E1No or slow drain detected; drain hose may not be put down or may be blocked by foreign…E2The machine stops running during washing, rinsing, or spinning due to the top lid not…E3Safety switch acts and spinning cannot work after two automatic amendment attempts; top…E4Heating coil damage or overload of laundry that leads to a failure to reach the set…E5Motor overheat protection or motor damage (door lock light glitters 7 times and stops 4…E6Water exceeds protective level (door lock light glitters 8 times and stops 4 seconds…E7The communication is bad (communication error between components).E8The dry temperature sensor is short cut or open.E9Door is not properly shut 20 seconds after program is started.EASpin lopsidedly (unbalanced load during spin).EbDoor is not closed before starting program.ECThe memory function (EEPROM) has failed.ELLaundry load is too much (overload).ELovInput voltage is lower than 93V.EndCycle or self-test has completed normally.Er12Water level abnormity during drying cycle, possibly caused by broken drain pump, abnormal…Er13Sheathed heating elements or drying motor abnormity during drying cycle.ErLCThe door cannot be locked.Err1Door lock fault-door not properly closed, door lock not linked or damaged, or related…Err10Lost communication between the power board and the display board.Err11Heating resistor relay may be broken.Err12Water level abnormalErr13Door unlock failureErr14Spin unbalanceErr2Drainage fault-water is not drained completely; the water/pressure switch does not return…Err3Temperature sensor fault-temperature sensor resistance is over specification (over 2Ω…Err4Heating fault-the temperature does not go up during heating; heating element issue.ERR5The required water level is not reached within 8 minutes, or the water level exceeds the…Err6Dry temperature sensor failureErr7Motor feedback signal failureErr8Water level overflow-the water level is over the protecting water level.Err9Lost communication between the power board and the display board.Error 1Door is not properly shut; the door lock light does not illuminate.Error 2Drainage error; water not emptied within 4 minutesError 3Water level not met in 8 minutesError 4Timing control damageError 5Motor overheat protection or damageError 6Water exceeds protective levelErULThe door lock cannot be opened (unlock failure).EundUnbalance error during spin cycle.FDraining does not work or the speed of draining is too slow.F2Overflow alarmFADrain hose set too low; the height of the end of the drain hose should be between…FErrMotor fault-the motor is broken or not functioning.HeaterThe heater may be broken.LDThe draining does not work, or the speed of draining is too slow.LFThe water inlet time exceeds the preset time (40 minutes).Motor overheatMotor overheat protection activated or motor is damaged.Motor speedMotor speed errorrinse/spin flashingDraining does not work or speed of draining is too slow; drain hose may not be put down…rinse+spin flashDraining does not work or the speed of draining is too slow; drain hose may not be put…SudToo much suds detected.Temperature sensorTemperature sensor (NTC) is not properly connected or damaged (displayed at end of…ULThe washer is out of balance.wash/rinse flashingSpinning cannot work due to imbalanced laundries or machine is not level; safety switch…wash/spin flashingProgram pauses after about 8 minutes of water inlet due to water faucet not open, water…wash+rinse flashDrainage does not work or draining speed is too slow; drain hose may not be put down or…wash+rinse flash quicklySafety switch activated; spinning cannot work due to imbalanced laundries or machine…WASH+RINSE+SPIN flash quicklyTop lid is not closed during wash, rinse, or spin cycle; machine stops operation.wash+rinse+spin flashingTop lid is not closed during wash/rinse/spin cycle, causing the machine to stop.WASH+SPIN flash quicklyWater inlet timeout; program pauses after about 8 minutes of water inlet due to closed…Water levelThe required water level is not reached within 10 minutes, or the water level exceeds the…Water level exceedsWater level exceeds protection value.
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for all brands and Max diagnostics, with 70 Max messages a day. Plus applicable tax.