mypros+
Error code reference

Haier Washer Error Code Eb

Door is not closed before starting program.

Haier codesHaier washer codes

Door is not closed before starting program.

First step from the service manual

Close the door properly.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for Eb.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What Eb means on a Haier washer

The Eb error code on a Haier washer indicates that the door was not fully closed and latched before a wash cycle was initiated. The washer's control board monitors the door lock and latch assembly through a dedicated circuit. When the program start command is received, the control board checks for a closed-door signal from the door switch or latch sensor. If that signal is absent, the machine halts and displays Eb to prevent the cycle from running with an open or improperly secured door.

The door latch assembly contains a mechanical latch and an integrated switch or sensor that sends a confirmation signal to the control board once the door is fully engaged. If the door is not pushed firmly shut, if an obstruction is preventing full closure, or if the latch mechanism is worn or faulty, the control board will not receive the expected closed-door confirmation. This safety interlock is a standard feature designed to prevent water from leaking out during operation and to protect users from contact with the drum while it is spinning.

In most cases, the Eb error is triggered by a simple user error and clears immediately once the door is firmly closed. However, repeated occurrences of this code without an obvious closure problem point toward a failing door latch assembly, a damaged door strike, or a wiring issue between the latch switch and the control board. Inspecting the door seal and hinge alignment is also worthwhile, as a misaligned door can prevent the latch from engaging even when the door appears closed.

Source: manufacturer service documentation.

Common causes of Eb

  1. 01

    Door not fully pushed shut

    Wiring / connection

    The most frequent cause is simply that the door was not closed with enough force to engage the latch fully. Push the door firmly until you hear or feel the latch click into place.

  2. 02

    Obstruction blocking door closure

    Wiring / connection

    A piece of clothing, a bra wire, or bulky fabric caught in the door opening can prevent the door from sealing completely. Check the drum opening and door gasket for any trapped items.

  3. 03

    Worn or broken door latch assembly

    Part replacement

    Over time, the mechanical latch or its integrated switch can wear out and fail to engage or send a proper signal to the control board. If the door closes but the error persists, the latch assembly likely needs replacement.

  4. 04

    Damaged door strike or hinge misalignment

    Part replacement

    A bent or cracked door strike can prevent the latch from catching, and a misaligned hinge can cause the door to sit at an angle that blocks full engagement. Inspect the strike plate and hinge points for visible damage or shifting.

  5. 05

    Faulty wiring between door switch and control board

    Part replacement

    If the latch mechanism appears intact but the Eb code continues, a loose connector or damaged wire in the door switch circuit may be preventing the closed-door signal from reaching the control board.

See the test procedure for each cause

Frequently asked questions about Eb

What does Eb mean on a Haier washer?
The Eb code on a Haier washer means the door was not detected as fully closed before the wash program was started. The washer uses a door latch switch to confirm that the door is securely shut, and if that confirmation signal is missing, it displays Eb and refuses to run. This is a safety feature that prevents the machine from operating with an open or unlatched door.
How do I fix the Eb error code on my Haier washer?
Start by pushing the door firmly closed until the latch clicks, then try starting the cycle again. Check the drum opening and door gasket for any clothing or debris that might be blocking full closure. If the error continues after the door is clearly shut, inspect the latch assembly and door strike for damage, and consider testing or replacing the door latch if it appears worn or broken.
Is it safe to use my Haier washer when the Eb error is showing?
The washer will not start a cycle while the Eb code is active, so there is no immediate safety risk. The error is a protective measure that keeps the machine from running with an unsecured door. Do not attempt to bypass or defeat the door latch, as operating the washer without a properly latched door can result in water leakage and contact with a spinning drum.
Will resetting my Haier washer clear the Eb error code?
Resetting the washer by unplugging it or canceling the cycle will clear the displayed error, but the code will return immediately if the underlying cause is not resolved. If the door is genuinely not latching, the Eb code will reappear as soon as you try to start a new cycle. A reset is only a lasting fix if the original trigger was a one-time user error, such as an incompletely closed door.
How much does it cost to repair a Haier washer showing the Eb error?
If the fix is simply closing the door properly, there is no cost involved. If the door latch assembly needs to be replaced, parts typically range from $15 to $60 depending on the specific model, and professional labor can add $75 to $150 or more to that total. Diagnosing and replacing a faulty wiring harness or door switch connector may fall within a similar cost range for labor.

Related Haier washer codes

All Haier washer codes
View all 66 Haier washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass