mypros+
Error code reference

Haier Washer Error Code Err1

Door lock fault

Haier codesHaier washer codes

Door lock fault – door not properly closed, door lock not linked or damaged, or related wiring harness broken.

First step from the service manual

Check whether the door is well closed.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for Err1.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What Err1 means on a Haier washer

The Err1 code on a Haier washer indicates a door lock fault. This error is triggered when the control board cannot confirm that the door is securely latched and locked before or during a wash cycle. The door lock system relies on a switch or sensor within the locking mechanism to send a confirmation signal to the main control board. When that signal is absent, interrupted, or incorrect, the machine halts operation and displays Err1 to prevent running with an unsecured door.

There are three primary conditions that can produce this error. First, the door may simply not be fully closed, which is the most straightforward cause and should always be checked first. Second, the door lock assembly itself may have failed mechanically or electrically, meaning the locking actuator or the integrated switch is no longer functioning correctly. Third, the wiring harness that connects the door lock mechanism to the control board may be broken, frayed, or have a loose connector, interrupting the continuity of the signal.

Diagnosing Err1 requires a systematic approach starting with the physical door closure, then moving to inspection of the lock linkage and latch condition, and finally checking the wiring harness for visible damage or disconnected terminals. If the door closes firmly and the latch engages but the error persists, the fault is most likely internal to the lock assembly or within the connecting wiring.

Source: manufacturer service documentation.

Common causes of Err1

  1. 01

    Door not fully closed

    Wiring / connection

    The door may not have been pushed firmly shut until the latch clicks into place. Check for laundry or debris caught in the door seal that could be preventing full closure.

  2. 02

    Faulty door lock assembly

    Part replacement

    The door lock mechanism, including its internal switch, may be worn out or damaged and no longer sending a proper confirmation signal to the control board. The lock may appear to engage but fail electrically.

  3. 03

    Broken or disconnected wiring harness

    Wiring / connection

    The wiring harness running between the door lock and the control board may have a broken wire, frayed insulation, or a loose connector terminal. Inspect the harness along its full length for visible damage.

  4. 04

    Damaged door latch or striker

    Part replacement

    The plastic latch on the door or the striker plate on the cabinet may be cracked or misaligned, preventing the lock from properly engaging even when the door is pushed shut.

  5. 05

    Door hinge misalignment

    Wiring / connection

    If the door hinges are worn or the door has sagged over time, the latch and lock mechanism may no longer align correctly, causing the lock to fail to engage fully.

See the test procedure for each cause

Frequently asked questions about Err1

What does Err1 mean on a Haier washer?
Err1 on a Haier washer indicates a door lock fault. The washer has detected that the door is not properly closed, that the door lock is not linking or functioning correctly, or that the wiring connected to the door lock is broken. The machine will not start or continue a cycle until this fault is resolved.
How do I fix the Err1 error on my Haier washer?
Start by firmly pushing the door shut until you hear or feel it latch, then try restarting the cycle. If the error returns, inspect the door latch and lock mechanism for visible damage and check the wiring harness for loose or broken connections. If the lock assembly itself is faulty, it will need to be replaced to clear the error.
Is it safe to use my Haier washer when Err1 is displayed?
No, you should not attempt to bypass or override the Err1 error. The door lock fault means the washer cannot confirm the door is secure, and running the machine in this state could result in the door opening during a cycle, causing water spillage or injury. Resolve the underlying fault before operating the washer.
Will resetting my Haier washer clear the Err1 code?
A reset may temporarily clear the Err1 display, but if the underlying cause such as a faulty lock, broken wiring, or a misaligned latch is still present, the error will return as soon as you attempt to run a cycle. A reset is not a fix and the root cause must be addressed.
How much does it cost to repair a Haier washer showing Err1?
If the fix is simply closing the door properly, there is no cost involved. Replacing a door lock assembly typically ranges from $40 to $120 for the part, with additional labor costs if a technician is needed. Wiring harness repairs can vary widely depending on the extent of the damage and whether the full harness or just a connector needs attention.

Related Haier washer codes

All Haier washer codes
View all 66 Haier washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass