mypros+
Error code reference

Haier Washer Error Code Error 3

Water level not met in 8 minutes

Haier codesHaier washer codes

Water level not met in 8 minutes. Door lock light flashes 5 times and stops for 4 seconds repeatedly.

First step from the service manual

Make sure that tap is turned on and water pressure is normal. If problem still exists, contact an authorized service personnel.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for Error 3.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What Error 3 means on a Haier washer

Error 3 on a Haier washer indicates that the machine failed to reach the required water level within an 8-minute fill window. The control board monitors water level through a pressure switch or sensor, and when sufficient water is not detected before the timer expires, the machine halts the cycle and triggers this fault. The door lock indicator light will flash 5 times, pause for 4 seconds, and repeat this pattern continuously as a visual signal of the fault condition.

The fill system involves several components working together: the water inlet valve, the water supply lines, the pressure switch, and the control board itself. If any part of this chain fails to deliver or detect the correct water volume in time, Error 3 will be triggered. The most straightforward cause is restricted water supply, such as a closed or partially open tap, kinked inlet hose, or low household water pressure. These should always be ruled out before suspecting internal component failure.

If the water supply checks out as normal, the fault may point to a failed or clogged water inlet valve that is not opening fully, a blocked inlet hose filter screen, or a faulty water level pressure switch that is not accurately reporting the fill status to the control board. In less common cases, a wiring fault between the inlet valve and the control board can prevent the valve from receiving the signal to open.

Source: manufacturer service documentation.

Common causes of Error 3

  1. 01

    Tap closed or water pressure too low

    Wiring / connection

    The water supply tap behind the washer may be partially or fully closed, or household water pressure may be too low to fill the drum within the 8-minute limit. Check that both hot and cold taps are fully open and confirm normal pressure at a nearby faucet.

  2. 02

    Kinked or blocked inlet hose

    Wiring / connection

    The water inlet hose running from the tap to the washer may be kinked, pinched, or have a clogged filter screen at the connection point. Inspect the hose for bends and check the small mesh filter screens at each end of the hose for sediment buildup.

  3. 03

    Faulty or clogged water inlet valve

    Part replacement

    The internal water inlet valve controls water flow into the drum and can fail mechanically or electrically, or become clogged with mineral deposits. A valve that does not open fully will restrict flow enough to cause a fill timeout.

  4. 04

    Defective water level pressure switch

    Part replacement

    The pressure switch monitors water level and signals the control board when the correct amount of water has entered the drum. If this switch is faulty or its connecting hose is blocked, it may incorrectly report that the required level has not been reached even when water is present.

  5. 05

    Wiring fault to the inlet valve

    Wiring / connection

    A damaged or disconnected wire between the control board and the water inlet valve can prevent the valve from receiving the signal to open. This would cause no water to enter the machine at all despite the supply being fully functional.

See the test procedure for each cause

Frequently asked questions about Error 3

What does Error 3 mean on a Haier washer?
Error 3 means the washer was unable to fill to the required water level within 8 minutes. The control board timed out waiting for the pressure switch to confirm adequate water in the drum. You will see the door lock light flashing 5 times repeatedly as a visual indicator of this fault. The cycle will not continue until the issue is resolved.
How do I fix Error 3 on a Haier washer?
Start by checking that the water supply taps are fully open and that water pressure is normal. Inspect the inlet hoses for kinks and check the filter screens at the hose connections for blockages. If the water supply is fine and the error persists, the water inlet valve or pressure switch may need to be inspected or replaced by a qualified technician.
Will resetting my Haier washer clear Error 3?
Resetting the washer by unplugging it for a minute and restarting may temporarily clear the error display, but if the underlying cause has not been fixed, the error will return as soon as the machine attempts to fill again. A reset is only a lasting fix if the error was triggered by a one-time issue such as a temporarily closed tap or a brief drop in water pressure.
Is it safe to keep using my Haier washer with Error 3 showing?
The washer will not proceed with the wash cycle while Error 3 is active, so there is no immediate safety risk from the error itself. However, you should not attempt to bypass the fault or force the machine to run without resolving the fill issue, as running the motor without adequate water can cause damage to internal components over time.
How much does it cost to repair Error 3 on a Haier washer?
If the fix is as simple as opening a tap or clearing a clogged filter screen, there is no parts cost involved. If the water inlet valve needs replacement, parts and labor typically range from $75 to $200 depending on your location and service rates. A faulty pressure switch is generally a lower-cost repair, with total costs usually falling in the $50 to $150 range.

Related Haier washer codes

All Haier washer codes
View all 66 Haier washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass