mypros+
Error code reference

Hotpoint Dishwasher Error Code AL07

Turbine damaged

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the AL07 error code actually means

Your Hotpoint dishwasher has detected water inside the tub but cannot confirm that water entered through the normal fill process, which has triggered a turbine fault alarm. This usually means a small flow-sensing part called the turbine is damaged, disconnected, or not working correctly. In rare cases, water poured manually into the tub can also cause this alert.

Diagnostic procedure

The full AL07 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check turbine connector for disconnection; check turbine cables for damage; check Main PCB/water meter turbine; check if turbine is faulty or wet; check if more than 1 litre of water has been filled manually to the tank.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock AL07 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of AL07

Ranked by how often they cause this code
  1. 1Faulty or damaged turbine
  2. 2Disconnected turbine connector
  3. 3Damaged turbine wiring
  4. 4Moisture or water ingress into the turbine
  5. 5Manual water addition to the tub

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about AL07

What does AL07 mean on a Hotpoint dishwasher?
AL07 indicates a turbine fault where the main PCB has detected water in the tank via the pressure switch but received no fill signal from the water meter turbine. This conflict between the two signals causes the control board to flag the error. It most commonly points to a damaged, disconnected, or wet turbine rather than an actual water leak or overfill event.
Is it safe to use my dishwasher while AL07 is showing?
It is not advisable to continue running the dishwasher with AL07 active. Because the control board cannot accurately track how much water is entering the tub, it cannot properly manage the fill cycle, which could result in underfilling or potential overfilling. Resolve the fault before running further wash cycles.
How much does it cost to repair an AL07 error on a Hotpoint dishwasher?
Repair costs vary depending on the root cause. If the fix is simply reseating a connector, there may be no parts cost, though a service call fee typically applies if a technician attends. Replacing a faulty water meter turbine generally involves parts costs in the range of $20 to $70 USD depending on the model, plus labour if professionally fitted. If the main PCB is at fault, costs rise considerably, often falling in the $100 to $300 USD range for parts and labour combined.
Can I fix an AL07 error myself without calling a technician?
Some causes of AL07 are straightforward to address at home, such as reseating a loose turbine connector or checking whether water was accidentally poured into the tub. However, if the turbine itself is physically damaged or the wiring harness is broken, replacement parts will be needed and the repair may require disassembly of the water inlet assembly. If you are comfortable working around appliance wiring and connectors, the connector and cable checks are reasonable DIY starting points.
Will resetting the dishwasher clear the AL07 error?
A reset may temporarily clear the AL07 code, but if the underlying cause such as a faulty turbine, damaged wiring, or disconnected connector has not been addressed, the error will return during the next fill cycle when the PCB again detects the signal conflict. A reset is useful for confirming whether the fault is persistent but is not a repair in itself.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass