mypros+
Error code reference

Indesit Dryer Error Code F05

Pump is not working when it should be on.

Indesit codesIndesit dryer codes

Pump is not working when it should be on.

First step from the service manual

Check security of module connector J5.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F05.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F05 means on a Indesit dryer

The F05 error code on an Indesit dryer indicates that the pump is not operating when the control system expects it to be active. This is a condenser dryer fault related to the condensate drainage system. The control module monitors pump operation during drying cycles, and when it detects that the pump has failed to activate or is not drawing current as expected, it triggers F05 and halts or interrupts the cycle to prevent water overflow or moisture buildup within the appliance cabinet.

The diagnostic process begins at connector J5 on the control module. A loose, corroded, or damaged connection at J5 can interrupt the signal or power supply to the pump circuit, causing the module to register a pump failure even when the pump itself is intact. This should always be checked first, as wiring and connector faults are among the most frequent causes of component-related error codes in this appliance range.

Beyond the connector, the fault can originate from the pump motor itself failing due to wear, a seized impeller from lint or debris accumulation, or a failed capacitor that supports pump startup. The control module may also be at fault if it is unable to send the correct output signal through the J5 connector circuit to activate the pump. Proper diagnosis requires isolating whether the fault is in the wiring path, the pump assembly, or the module output.

Source: manufacturer service documentation.

Common causes of F05

  1. 01

    Loose or faulty J5 module connector

    Wiring / connection

    A loose, corroded, or damaged connector at J5 on the control module can interrupt the pump circuit, causing a false or genuine pump failure reading. Inspect the connector for secure seating, corrosion, and damaged pins.

  2. 02

    Blocked or seized pump impeller

    Wiring / connection

    Lint, debris, or scale buildup can jam the pump impeller, preventing it from spinning when activated. Removing and inspecting the pump for obstructions can confirm this cause.

  3. 03

    Failed pump motor

    Part replacement

    The pump motor windings can fail due to wear or overheating, causing the pump to draw no current when the module attempts to activate it. A failed motor will require pump replacement.

  4. 04

    Wiring harness damage between module and pump

    Part replacement

    Damaged, broken, or shorted wiring between the J5 connector and the pump assembly can prevent the activation signal or power from reaching the pump. A visual inspection and continuity check of the harness will identify breaks.

  5. 05

    Control module output failure

    Part replacement

    If the module's pump output circuit has failed, it will be unable to energize the pump regardless of the pump's condition. This is typically diagnosed after all other components in the circuit have been confirmed functional.

See the test procedure for each cause

Frequently asked questions about F05

What does F05 mean on a Indesit dryer?
F05 on an Indesit dryer means the control module has detected that the pump is not working when it should be active during the drying cycle. The pump is responsible for removing condensed water from the appliance. The dryer stops operation to prevent internal water overflow. The first step in diagnosis is checking the security of the J5 connector on the control module.
Can I fix the F05 error myself on an Indesit dryer?
Some causes of F05 are accessible to a confident DIYer, such as reseating the J5 module connector or clearing a blocked pump impeller. Wiring checks and component replacements like a pump motor require basic electrical knowledge and safe isolation of the appliance from the power supply. If you are unsure about working inside the dryer, a qualified technician should perform the diagnosis.
Is it safe to use my Indesit dryer when F05 is showing?
No, you should not continue using the dryer while F05 is active. The error indicates the condensate pump is not functioning, which means water is not being removed as intended. Continued use could result in water accumulating inside the cabinet and potentially damaging other components. Switch off and unplug the appliance until the fault is resolved.
Will resetting the dryer clear the F05 error code?
A reset may temporarily clear the F05 code, but if the underlying fault is not repaired, the error will return once the pump is called upon again during a cycle. Resetting without addressing the root cause, such as a faulty connector, blocked pump, or failed motor, will not resolve the problem. A proper diagnosis of the pump circuit is necessary for a lasting fix.
How much does it cost to repair an F05 error on an Indesit dryer?
Repair costs depend on the cause of the fault. If the issue is simply a loose J5 connector, there may be no parts cost involved, with only a service call fee if a technician is used. Pump replacement typically falls in the range of 40 to 100 dollars or pounds for the part, plus labor. Control module replacement represents the higher end of repair costs and may range from 80 to 200 dollars or pounds including labor.

Related Indesit dryer codes

All Indesit dryer codes
View all 15 Indesit dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass