mypros+
Error code reference

Kenmore Washer Error Code E95

Communication error.

Kenmore codesKenmore washer codes

Communication error.

First step from the service manual

Replace the control board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E95.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E95 means on a Kenmore washer

The E95 error code on a Kenmore washer indicates a communication error between internal control components. This type of fault occurs when the main control board loses the ability to send or receive data signals from other electronic modules in the machine. The communication pathway between the control board and secondary components relies on consistent voltage and clean signal lines, and any disruption to those pathways will trigger this code.

The most common root cause of E95 is a failure within the main control board itself, which is why replacing the control board is the recommended first diagnostic step. Internal failures such as damaged microprocessors, burned relay contacts, or degraded capacitors on the board can cause signal transmission to break down entirely. Wiring harness issues, including loose connectors, corroded terminals, or pinched wires running between control components, can also produce this fault.

Because the error points to a control-level communication breakdown rather than a mechanical component failure, diagnostics should focus on the electronic control system. Technicians should inspect all wiring connections to and from the main control board before condemning the board outright, as a loose or corroded connector can mimic a board failure. If connections are secure and undamaged, control board replacement is the appropriate next step.

Source: manufacturer service documentation.

Common causes of E95

  1. 01

    Failed main control board

    Part replacement

    The control board itself may have internal component failures that prevent it from sending or receiving signals. This is the primary suspect and the recommended first replacement based on diagnostic guidance.

  2. 02

    Loose or disconnected wiring harness

    Wiring / connection

    Connectors between the control board and other electronic modules can work loose over time from vibration during wash cycles. Inspect all harness connections at the control board for secure seating.

  3. 03

    Corroded or damaged wire terminals

    Wiring / connection

    Moisture exposure inside the washer cabinet can cause terminal corrosion at connector points, degrading the signal pathway enough to trigger a communication fault. Look for discoloration or buildup at connector pins.

  4. 04

    Pinched or damaged wiring

    Part replacement

    Wires routed through the cabinet can become pinched or frayed, interrupting the communication signal between control components. A visual inspection of wire routing paths can help identify physical damage.

See the test procedure for each cause

Frequently asked questions about E95

What does E95 mean on a Kenmore washer?
E95 on a Kenmore washer indicates a communication error within the machine's electronic control system. It means the main control board is unable to properly exchange data signals with other components. This is a control-level fault, not a mechanical one, and typically requires inspection of the control board and associated wiring.
Can I fix the E95 error code myself?
Some basic checks, like inspecting wiring harness connectors for looseness or visible damage, can be performed by a knowledgeable DIYer. However, if the wiring connections are intact and the error persists, the main control board likely needs to be replaced, which is a more involved repair. Technicians with experience in appliance electronics are best suited for this type of diagnosis and repair.
Is it safe to use my Kenmore washer when E95 is displayed?
It is generally not recommended to continue running the washer when the E95 error is active. A communication failure between control components can lead to unpredictable machine behavior, including failure to stop a cycle properly. Discontinue use and address the error before running additional loads.
How much does it cost to repair the E95 error on a Kenmore washer?
Repair costs for E95 depend on whether the fix requires a new control board or just a wiring correction. If only wiring connectors need reseating, the cost may be limited to a service call fee, typically in the range of $75 to $150. Control board replacement parts and labor combined can range from $200 to $450 or more depending on the specific model and service provider.
Will resetting my Kenmore washer clear the E95 error code?
A power reset by unplugging the washer for a few minutes may temporarily clear the E95 code, but it is unlikely to resolve the underlying issue. If the communication fault is caused by a failing control board or damaged wiring, the error will return once the washer attempts to operate again. A proper repair of the root cause is needed for a lasting fix.

Related Kenmore washer codes

All Kenmore washer codes
View all 156 Kenmore washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass