mypros+
Error code reference

LG Air Conditioner Error Code 10

Poor indoor fan motor operation; disconnected fan motor connector or indoor fan motor lock/failure.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 10 error code actually means

Your LG air conditioner's indoor unit fan motor has stopped sending a signal to the system's control board, which means the unit cannot confirm the fan is running. The air conditioner shuts down to protect itself. This could be something as simple as a loose wire plug, or it may mean the fan motor itself needs to be replaced.

Diagnostic procedure

The full 10 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Remove motor connector; turn the fan by hand and check whether it is locked.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 10 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 10

Ranked by how often they cause this code
  1. 1Loose or disconnected motor connector
  2. 2Failed BLDC fan motor
  3. 3Damaged wiring harness
  4. 4Faulty main control board
  5. 5Obstruction preventing motor rotation

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 10

What does 10 mean on a LG air conditioner?
Error code 10 on an LG air conditioner means the indoor unit's BLDC fan motor has failed to send a feedback signal to the control board for 50 consecutive seconds. The system cannot confirm the fan is operating and shuts down as a protective measure. The fault points to the indoor fan motor circuit, which includes the motor itself, its wiring harness, and the main control board.
Is it safe to keep running my LG air conditioner with error code 10?
No. When error code 10 is active, the indoor fan motor is not confirmed to be running, which means the unit cannot properly circulate air over the evaporator coil. Running the system in this state risks freezing the coil and can cause refrigerant or compressor damage over time. The unit should remain off until the fault is diagnosed and resolved.
Will resetting my LG air conditioner clear error code 10?
A power reset may temporarily clear the error code display, but the fault will return within 50 seconds if the underlying problem with the fan motor feedback signal has not been corrected. Resetting the unit without addressing the root cause does not fix the motor circuit and can delay proper diagnosis. The error should be treated as an active fault requiring inspection rather than a one-time glitch.
Can I fix error code 10 on my LG air conditioner myself?
The first step, checking that the motor connector is fully and properly seated, is a straightforward task that a careful DIYer can perform after disconnecting power to the unit. If the connector is secure and the error returns, further diagnosis involves checking wiring continuity and motor function, which requires a multimeter and some electrical knowledge. Replacing the fan motor or control board is more involved and is generally best handled by a qualified technician.
How much does it cost to repair error code 10 on an LG air conditioner?
Repair costs depend on the root cause. If the issue is simply a loose connector, there may be no parts cost beyond a service call, which typically ranges from $75 to $150. A replacement BLDC indoor fan motor generally costs between $80 and $200 for the part, with labor adding $100 to $200 depending on the unit type and accessibility. A main control board replacement can range from $150 to $350 or more for parts alone.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass