mypros+
Error code reference

LG Dishwasher Error Code bC

Button/key input error (S/W ver. 7134+)

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the bC error code actually means

The bC code means your dishwasher detected that one of its buttons was being held down for 30 seconds or more, which it flags as an error. This could be caused by a stuck button, moisture on the control board, or a faulty control panel. The good news is your dishwasher will finish the current wash cycle even while this code is displayed.

Diagnostic procedure

The full bC procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check whether there is condensation on the PBA connectors.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock bC procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of bC

Ranked by how often they cause this code
  1. 1Condensation on PBA Connectors
  2. 2Stuck or Jammed Control Panel Button
  3. 3Faulty Membrane Switch or Touchpad
  4. 4Damaged Wiring Harness Between UI and PBA
  5. 5Failed PBA Control Board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about bC

What does bC mean on a LG dishwasher?
The bC code on an LG dishwasher indicates a button or key input error, specific to software version 7134 and later. It means the control board has detected that a button was held or registered as continuously pressed for 30 seconds or longer. The dishwasher treats this sustained signal as a fault but will continue running through the rest of the current cycle rather than stopping immediately.
Is it safe to keep using my LG dishwasher when the bC code is showing?
The bC error does not indicate a water leak, electrical hazard, or mechanical failure that would make continued use immediately dangerous. The dishwasher is designed to complete the current cycle even with the code active. However, you should address the underlying cause promptly, as a faulty control input can affect how the machine responds to commands over time.
How much does it cost to repair the bC error on an LG dishwasher?
Repair costs depend heavily on the root cause. If the fix is simply drying out condensation on the PBA connectors, there may be no parts cost at all, only a service call fee if a technician is involved. Touchpad or membrane switch replacement typically ranges from around 50 to 150 dollars in parts, while a full PBA control board replacement can range from 100 to 300 dollars or more in parts, plus any applicable labor costs.
How do I fix the bC error on my LG dishwasher?
Start by checking the PBA connectors for condensation or moisture, as this is the primary diagnostic step. If moisture is present, disconnect power, allow the connectors to dry thoroughly, and reconnect them. If the error persists, inspect the control panel buttons for any that feel stuck, and check the wiring harness between the panel and the control board. If none of those resolve the issue, the touchpad or control board may need replacement.
Will resetting my LG dishwasher clear the bC error code?
A power reset by unplugging the dishwasher or turning off the circuit breaker for a few minutes may temporarily clear the bC code. However, if the underlying cause, such as a stuck button, moisture on the PBA connectors, or a faulty touchpad, is not corrected, the code will return. A reset alone is not a fix, just a way to confirm whether the fault is intermittent or persistent.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass