mypros+
Error code reference

Maytag Dryer Error Code EE PROM FAULT ###

Error in memory location; the ### indicates the specific location of the fault.

Maytag codesMaytag dryer codes

Error in memory location; the ### indicates the specific location of the fault.

MyPros+ Max

Get the full diagnostic procedure for EE PROM FAULT ###.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What EE PROM FAULT ### means on a Maytag dryer

The EE PROM FAULT ### error on a Maytag dryer indicates a failure or corruption within the EEPROM (Electrically Erasable Programmable Read-Only Memory) on the main control board. The EEPROM is a small non-volatile memory chip that stores critical configuration data, cycle parameters, and operational settings for the dryer. The three-digit numeric code that follows the fault label pinpoints the specific memory address or location where the error was detected, which can help narrow down whether the issue is with stored cycle data, calibration values, or other programmed parameters.

EEPROM faults are almost always traced back to the main control board itself. The memory chip is soldered directly onto the board, so it cannot be replaced independently in the field. Causes include voltage spikes or power surges that corrupt stored data, physical damage to the board from heat or moisture, and age-related degradation of the memory chip. In some cases, a temporary power interruption during a write cycle can corrupt a specific memory location, which explains why the fault code includes a precise address.

Because the EEPROM is integral to the control board, resolving this fault typically requires replacing the entire main control board assembly. Before replacing the board, technicians should attempt a hard reset by disconnecting power to the dryer for several minutes to see if the fault clears. If the error returns after restoring power, the control board is the confirmed failed component and will need to be sourced and installed.

Source: manufacturer service documentation.

Common causes of EE PROM FAULT ###

  1. 01

    Failed or corrupted main control board EEPROM

    Part replacement

    The EEPROM chip on the control board has degraded or its stored data has become corrupted. This is the most common cause and is confirmed when the fault code persists after a full power reset.

  2. 02

    Power surge or voltage spike

    Part replacement

    A sudden surge in line voltage can corrupt data stored in specific EEPROM memory locations. Check the power supply and consider surge protection if the board is replaced.

  3. 03

    Interrupted write cycle due to power loss

    Wiring / connection

    If power was cut to the dryer while it was actively writing data to the EEPROM, the targeted memory location can be left in a corrupted state. A hard reset may resolve this in rare cases.

  4. 04

    Heat or moisture damage to the control board

    Part replacement

    Excessive heat buildup inside the control panel or moisture infiltration can physically damage the EEPROM chip or its surrounding circuitry. Inspect the board for visible burn marks, discoloration, or corrosion.

See the test procedure for each cause

Frequently asked questions about EE PROM FAULT ###

What does EE PROM FAULT ### mean on a Maytag dryer?
This error indicates a fault at a specific location within the EEPROM memory chip on the main control board. The numeric code following the fault label identifies the exact memory address where the problem was detected. The EEPROM stores operational settings and cycle data, and when it fails or becomes corrupted, the dryer cannot function normally. In most cases, the main control board will need to be replaced.
Can I fix the EE PROM FAULT ### error myself?
Start by disconnecting the dryer from power for several minutes, then restore power to see if the fault clears. If the error returns, the main control board is likely faulty and will need to be replaced. Replacing a control board is within reach for experienced DIYers who are comfortable working with appliance electronics and following proper safety precautions, including disconnecting power before starting any work.
Is it safe to use my Maytag dryer when it shows EE PROM FAULT ###?
It is generally not recommended to continue operating the dryer when this fault is active, as the corrupted memory can cause unpredictable behavior in cycle control and heating functions. Running the dryer in this state could lead to incomplete drying cycles or other operational issues. Resolve the fault before resuming normal use.
How much does it cost to repair an EE PROM FAULT ### on a Maytag dryer?
If the main control board needs replacement, parts typically range from around $100 to $250 depending on the specific model. Adding professional labor, the total repair cost commonly falls between $150 and $400. Attempting a DIY repair can reduce costs significantly if you are comfortable sourcing and installing the part yourself.
Will resetting my Maytag dryer clear the EE PROM FAULT ### error?
A hard reset, performed by disconnecting the dryer from power for several minutes, can sometimes clear the fault if it was caused by a temporary power interruption during a memory write cycle. However, if the EEPROM chip itself has degraded or the control board was damaged by a power surge, the error will return after the reset. A persistent fault after reset confirms the control board needs to be replaced.

Related Maytag dryer codes

All Maytag dryer codes
View all 251 Maytag dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass