mypros+
Error code reference

Miele Refrigerator Error Code 3-4-2

Icemaker

Miele codesMiele refrigerator codes

Icemaker: Internal fault.

First step from the service manual

Switch appliance off and on; if fault returns, check water inlet heater at back of appliance; if functioning, replace icemaker.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 3-4-2.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 3-4-2 means on a Miele refrigerator

Error code 3-4-2 on a Miele refrigerator indicates an internal fault within the icemaker system. This code is triggered when the icemaker's control circuitry detects an operating condition outside of normal parameters, which can include issues with the water delivery path, heating components, or the icemaker unit's own internal electronics. Because the fault is classified as internal, it typically points to a failure within the icemaker assembly itself or a supporting component that the icemaker depends on to complete its cycle.

The diagnostic path for this fault begins with the water inlet heater located at the back of the appliance. This heater prevents the water inlet from freezing, which would block water flow into the icemaker and trigger a fault condition. If the water inlet heater is non-functional, water cannot reliably enter the icemaker, causing the unit to register an internal error. Checking this heater for continuity and proper operation is the recommended first step before condemning the icemaker itself.

If the water inlet heater tests functional and the fault persists after cycling power to the appliance, the icemaker module itself is the likely cause and should be replaced. A power cycle can sometimes clear transient electronic faults, but a recurring 3-4-2 code indicates a persistent hardware issue. Continued operation without addressing the fault will result in no ice production.

Source: manufacturer service documentation.

Common causes of 3-4-2

  1. 01

    Failed water inlet heater

    Part replacement

    The water inlet heater at the back of the appliance keeps the water supply line from freezing. If this heater fails, water cannot reach the icemaker, triggering an internal fault. Check the heater for continuity to confirm whether it is functioning.

  2. 02

    Internal icemaker module failure

    Part replacement

    The icemaker's own control board or internal components can fail, producing a persistent 3-4-2 fault that does not clear after a power cycle. If the water inlet heater tests good and the fault returns after resetting, the icemaker unit itself needs to be replaced.

  3. 03

    Transient electronic fault

    Wiring / connection

    Occasionally, a temporary power fluctuation or software glitch can cause the icemaker to log a fault code. Switching the appliance off and back on may clear the code if no underlying hardware failure is present.

  4. 04

    Frozen water supply to icemaker

    Wiring / connection

    If the water inlet heater is borderline functional or the freezer temperature is set too low, ice can block the water path into the icemaker. This restricts water flow and can cause the icemaker to register an internal fault.

See the test procedure for each cause

Frequently asked questions about 3-4-2

What does 3-4-2 mean on a Miele refrigerator?
Error code 3-4-2 on a Miele refrigerator indicates an internal fault with the icemaker. The code signals that the icemaker has detected an operating condition it cannot resolve, which may involve the water inlet heater at the back of the appliance or a failure inside the icemaker unit itself. The icemaker will not produce ice while this fault is active.
Can I fix error code 3-4-2 myself?
The first step is to switch the refrigerator off and back on to see if the fault clears on its own. If it returns, the water inlet heater at the back of the appliance should be checked for proper function. If that component tests good, replacing the icemaker module is the recommended fix, which is a task many experienced DIYers can handle, though it does require accessing internal components.
Is it safe to keep using my Miele refrigerator with error code 3-4-2?
The refrigerator's cooling and food preservation functions are generally not affected by this fault, as 3-4-2 is specific to the icemaker system. However, the icemaker will not operate correctly while the code is active. It is still advisable to address the fault promptly to avoid any secondary issues with water components.
Will resetting my Miele refrigerator clear error code 3-4-2?
A power cycle, switching the appliance off and then back on, can clear the code if the fault was caused by a temporary electronic glitch. If the code returns after the reset, the fault is persistent and indicates a hardware issue with either the water inlet heater or the icemaker module itself. Repeated resets without fixing the underlying cause will not resolve the problem.
How much does it cost to repair error code 3-4-2 on a Miele refrigerator?
Repair costs depend on which component has failed. Replacing the water inlet heater is generally the less expensive repair, with parts and labor typically ranging from around $100 to $250. If the icemaker module itself needs to be replaced, costs can range from approximately $250 to $600 or more depending on labor rates and parts pricing for Miele appliances.

Related Miele refrigerator codes

All Miele refrigerator codes
View all 68 Miele refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass