mypros+
Error code reference

Samsung Dryer Error Code Et

Check the heater thermistor; for gas models, check that gas is supplied continually.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Et error code actually means

The Et error means your dryer has detected a problem with the temperature sensor near the heating system, so it stopped the heating function to stay safe. On a gas dryer, it can also appear if the dryer is not getting a steady supply of gas. Until this is fixed, your dryer will not heat properly.

Diagnostic procedure

The full Et procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check the Heater thermistor; in the case of gas model, check for continuous gas supply.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Et procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of Et

Ranked by how often they cause this code
  1. 1Faulty heater thermistor
  2. 2Loose or damaged thermistor wiring
  3. 3Interrupted gas supply (gas models only)
  4. 4Failed control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Et

What does Et mean on a Samsung dryer?
The Et code indicates that the Samsung dryer has detected a fault in the heater thermistor circuit. The thermistor monitors temperature near the heating assembly and communicates with the control board via resistance readings. On gas models, the code can also appear when gas is not being supplied continuously to the burner. The dryer will stop heating until the issue is resolved.
Is the Et error on a Samsung dryer a safety concern?
The dryer displays Et and disables heating as a protective measure, so continuing to run the machine with this fault active is not recommended. On a gas model, if you suspect a gas supply issue, confirm there are no gas leaks before troubleshooting further. A faulty thermistor that goes unaddressed could prevent the dryer from properly regulating temperature in future cycles.
Will resetting my Samsung dryer clear the Et error code?
A power reset, such as unplugging the dryer for a few minutes, may temporarily clear the Et code, but it will return if the underlying issue is not corrected. If the thermistor is defective, the wiring is damaged, or gas supply is inconsistent, the fault condition will be detected again as soon as the dryer attempts to heat. A reset is useful for confirming whether the fault is intermittent, but it is not a fix.
Can I fix the Et error myself?
Some causes of the Et error are DIY-friendly. Checking that the gas supply valve is fully open on a gas model costs nothing and takes only a moment. Inspecting and reseating the thermistor wiring connector is also straightforward for someone comfortable working inside an appliance. Replacing the thermistor itself is a moderate repair, but if the control board is at fault, that replacement is more complex and may be better handled by a technician.
How much does it cost to repair the Et error on a Samsung dryer?
If only the heater thermistor needs replacement, parts typically range from $10 to $40 depending on the model, and a technician's labor for this repair generally falls in the $80 to $150 range. If the control board is the root cause, board replacement parts and labor can run $150 to $350 or more. Getting the wiring and thermistor diagnosed first can help avoid unnecessary parts costs.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass