mypros+
Error code reference

Speed Queen Washer Error Code E:OF

IR communication has been turned off on the electronic control.

Speed Queen codesSpeed Queen washer codes

IR communication has been turned off on the electronic control.

First step from the service manual

Turn IR communication on (refer to programming manual).

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E:OF.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E:OF means on a Speed Queen washer

The E:OF error code on a Speed Queen washer indicates that IR (infrared) communication has been disabled in the electronic control board's settings. This is a configuration-level condition rather than a hardware failure. Speed Queen washers use infrared communication capability within the control system to interface with programming tools, service equipment, or networked appliance management systems. When this feature is toggled off, the control board flags E:OF to alert a technician that the IR channel is inactive.

This condition is typically encountered during or after a programming session, factory reset, or accidental modification of the control board's configuration parameters. It is not caused by a broken component in most cases. The control board stores IR communication settings in its memory, and those settings can be altered through the programming interface. If the IR function is disabled, certain communication-dependent diagnostics or remote features will not operate until the setting is restored.

The resolution is straightforward: access the programming menu on the electronic control and re-enable IR communication according to the programming manual for the specific model. No parts replacement is typically required. However, if the setting cannot be saved or the control reverts to IR-off status repeatedly, the control board itself may have a memory or firmware issue that warrants further inspection.

Source: manufacturer service documentation.

Common causes of E:OF

  1. 01

    IR Communication Disabled in Programming Settings

    Wiring / connection

    The most common cause is that the IR communication setting was manually turned off during a prior programming or setup session. Accessing the control's programming menu will confirm whether the IR setting is toggled off.

  2. 02

    Accidental Configuration Change

    Wiring / connection

    Navigating through the control board's programming interface without care can inadvertently disable IR communication. This can happen during diagnostic procedures or routine service visits.

  3. 03

    Control Board Reset Defaulting to IR Off

    Wiring / connection

    Some factory resets or power interruptions can cause the control board to revert to default settings, which may include IR communication being disabled. Checking the full settings profile after any reset is advisable.

  4. 04

    Control Board Memory or Firmware Issue

    Part replacement

    If the IR setting is re-enabled but the error returns repeatedly, the control board may have a firmware corruption or memory fault preventing settings from saving correctly. This scenario may require control board replacement.

See the test procedure for each cause

Frequently asked questions about E:OF

What does E:OF mean on a Speed Queen washer?
E:OF means the IR (infrared) communication feature has been turned off in the electronic control board's settings. This is a configuration issue, not a hardware failure. The code alerts technicians that the IR channel is inactive and needs to be re-enabled through the programming menu.
How do I fix the E:OF error on my Speed Queen washer?
To resolve E:OF, access the electronic control's programming menu and turn IR communication back on, following the steps in the programming manual for your specific model. No tools or parts are typically needed for this fix. If the setting will not save or the error keeps returning, the control board may need further diagnosis.
Will resetting my Speed Queen washer clear the E:OF error?
A basic power reset is unlikely to clear E:OF because the error reflects a saved setting within the control board's configuration memory. The IR communication setting must be explicitly re-enabled through the programming interface. In some cases, a factory reset could actually cause this error if it defaults the IR setting to off.
Is it safe to use my Speed Queen washer when E:OF is displayed?
The E:OF code relates to a communication configuration setting and does not indicate a mechanical or electrical hazard. In many cases the washer may still complete cycles, but certain diagnostic or communication-dependent functions will not work while IR is disabled. It is best to resolve the setting before relying on the machine for regular use.
How much does it cost to fix the E:OF error on a Speed Queen washer?
If the fix only requires re-enabling the IR setting in the programming menu, the cost is limited to a service call fee, typically in the range of $75 to $150 depending on your area. If the control board has a memory or firmware fault causing the setting not to save, control board replacement could add $150 to $400 or more in parts and labor.

Related Speed Queen washer codes

All Speed Queen washer codes
View all 71 Speed Queen washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass