mypros+
Error code reference

Speed Queen Washer Error Code Er, FL

The washer has not reached the fill level after 30 minutes during a wash or rinse fill.

Speed Queen codesSpeed Queen washer codes

The washer has not reached the fill level after 30 minutes during a wash or rinse fill.

First step from the service manual

Make sure hot and cold water faucets are turned on. Make sure fill hoses are not kinked or twisted. Clean the screens in the water mixing valve and the filter screens at the faucet end of the fill hoses. Unplug the machine for 15 seconds to clear this code.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for Er, FL.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What Er, FL means on a Speed Queen washer

The Er, FL error code on a Speed Queen washer indicates a fill timeout fault. The machine monitors water level through a pressure switch or sensor during wash and rinse fill cycles. If the washer does not reach the required fill level within 30 minutes of beginning a fill cycle, the control board logs this fault and halts operation. The 30-minute threshold is generous by design, meaning the error almost always points to a genuine supply or inlet restriction problem rather than a sensor issue.

The most common root causes involve the water supply itself. Both hot and cold water faucets must be fully open for the machine to fill at the correct rate. Kinked or twisted fill hoses can restrict flow significantly, especially if the washer has been pushed back against a wall. The inlet screens inside the water mixing valve and the filter screens at the faucet connections are frequent culprits, as sediment and mineral deposits accumulate over time and progressively reduce flow until the machine can no longer fill within the allowed window.

If supply and hose conditions check out, the fault may lie with the water mixing valve itself, which may have a failed solenoid coil preventing one or both water inlets from opening fully. A faulty pressure switch or water level sensor could also cause the control board to misread the fill status, triggering the error even when water is present. Clearing the code requires unplugging the machine for at least 15 seconds to reset the control board before restarting a cycle.

Source: manufacturer service documentation.

Common causes of Er, FL

  1. 01

    Closed or partially closed water supply faucets

    Wiring / connection

    If either the hot or cold water faucet behind the washer is not fully open, water flow will be too slow to reach the required fill level in time. Check both valves and turn them fully counterclockwise to confirm they are open.

  2. 02

    Clogged inlet screens or hose filter screens

    Wiring / connection

    Sediment, rust particles, and mineral deposits collect in the small mesh screens located at the water mixing valve inlets and at the faucet end of the fill hoses. Blocked screens restrict flow enough to trigger a fill timeout and must be removed and rinsed clean.

  3. 03

    Kinked or twisted fill hoses

    Wiring / connection

    Fill hoses that are bent sharply or pinched, often from the washer being pushed too close to the wall, can severely limit water flow. Inspect the full length of both hot and cold hoses and reposition the washer if needed to allow the hoses to run without bends.

  4. 04

    Failed water mixing valve solenoid

    Part replacement

    The water mixing valve uses individual solenoid coils to open the hot and cold water inlets. If one or both solenoids fail, the valve will not open fully or at all, preventing adequate fill flow even when supply pressure and hoses are in good condition. A failed valve requires replacement.

  5. 05

    Faulty water level pressure switch or sensor

    Part replacement

    The pressure switch signals the control board when the tub has reached the correct fill level. If the switch is defective or the hose connecting it to the tub is clogged or cracked, the board may never receive the fill-complete signal, causing a false timeout error.

See the test procedure for each cause

Frequently asked questions about Er, FL

What does Er, FL mean on a Speed Queen washer?
Er, FL is a fill timeout error, meaning the washer did not reach its required water level within 30 minutes during a wash or rinse fill cycle. The machine stops and displays this code to alert you to a water supply problem. The most common causes are closed faucets, kinked hoses, or clogged inlet screens at the hose connections. Unplugging the washer for 15 seconds after addressing the supply issue will reset the error.
How do I fix the Er, FL error on my Speed Queen washer?
Start by confirming that both the hot and cold water faucets behind the washer are fully open. Inspect both fill hoses for kinks or tight bends, and straighten them if needed. Remove the fill hoses from both the faucets and the water mixing valve on the back of the washer, then clean the small mesh filter screens at each connection point. After correcting any supply issues, unplug the washer for 15 seconds and plug it back in to clear the fault code before restarting your cycle.
Is it safe to keep using my Speed Queen washer when the Er, FL code appears?
The washer stops the cycle automatically when this error occurs, so there is no immediate safety risk. However, you should not attempt to bypass the error and force the machine to run, as operating with inadequate water fill can stress the motor and pump components. Diagnose and correct the water supply issue before resuming normal use.
Will resetting my Speed Queen washer clear the Er, FL code?
Unplugging the washer for 15 seconds will clear the Er, FL code from the display, but the code will return on the next cycle if the underlying fill problem has not been corrected. Always address the root cause, such as cleaning clogged screens or opening the supply faucets fully, before resetting the machine. A reset without fixing the supply issue will result in another 30-minute fill timeout and the same error.
How much does it cost to repair a Speed Queen washer showing the Er, FL error?
If the issue is simply clogged inlet screens or a kinked hose, the repair costs nothing beyond your time. If the water mixing valve solenoid has failed, the replacement part typically costs in the range of $30 to $80 depending on the specific model, plus labor if you hire a technician. A service call for a professional repair generally runs in the range of $100 to $200 total, though costs vary by region and service provider.

Related Speed Queen washer codes

All Speed Queen washer codes
View all 71 Speed Queen washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass