mypros+
Error code reference

Speed Queen Washer Error Code OF, St

The washtub has filled to the overflow level.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the OF, St error code actually means

Your Speed Queen washer has filled with more water than it should, triggering a safety stop to prevent overflow or flooding. You can press the Start/Pause button to let the machine spin out the excess water and attempt to recover. If the underlying cause is not fixed, the problem will likely happen again.

Diagnostic procedure

The full OF, St procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Press Start/Pause button; the machine will begin to spin to attempt to pump water out. If Start/Pause is not pressed within five minutes, Er, OF will be displayed and the machine will need to be unplugged for 15 seconds to clear the code.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock OF, St procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of OF, St

Ranked by how often they cause this code
  1. 1Faulty water inlet valve
  2. 2Defective water level pressure switch
  3. 3Clogged or kinked pressure switch hose
  4. 4Control board malfunction
  5. 5Excessively high household water pressure

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about OF, St

What does OF, St mean on a Speed Queen washer?
OF, St means the washtub has filled with water up to the overflow level, triggering a protective stop in the wash cycle. The machine detects this condition through its water level sensing system and halts operation to prevent flooding. Pressing the Start/Pause button within five minutes will initiate a spin to pump out the excess water. If that window is missed, the code escalates to Er, OF and the machine must be unplugged for 15 seconds to reset.
Will unplugging my Speed Queen washer clear the OF, St error?
Unplugging the machine for 15 seconds is required only if the error escalates to Er, OF, which happens when Start/Pause is not pressed within five minutes of OF, St appearing. Simply clearing the code will not fix the underlying cause of the overfill, so the error is likely to return if the faulty component is not repaired or replaced.
How much does it cost to repair a Speed Queen washer showing an OF, St error?
Repair costs depend on which component has failed. A replacement water inlet valve typically runs in the range of $25 to $75 for the part, while a water level pressure switch generally costs between $15 and $50. If professional labor is involved, total repair costs including diagnosis and parts can range from $100 to $250 or more depending on your location and the specific component requiring replacement.
How do I fix the OF, St error on my Speed Queen washer?
Start by pressing the Start/Pause button to trigger a spin and drain the excess water. Once the tub is clear, inspect the water inlet valve for signs of failure, check the pressure switch hose for kinks or blockages, and test the water level pressure switch. If the inlet valve is not closing fully, replacing it is typically the most direct fix for a recurring overfill condition.
Is it safe to use my Speed Queen washer when the OF, St code appears?
You should not run a new wash cycle until the cause of the overfill has been identified and corrected. An overfill condition can result in water spilling onto the floor, which creates a slip hazard and potential water damage to flooring and nearby structures. The machine's built-in recovery step, pressing Start/Pause to spin out the water, is safe to use, but continuing to operate the washer without addressing the root cause is not recommended.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass