mypros+
Error code reference

Sub-Zero Wine Storage Error Code 35 1 00

Zone 1 evaporator fan open circuit.

Sub-Zero codesSub-Zero wine storage codes

Zone 1 evaporator fan open circuit.

First step from the service manual

Check control board and fan.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 35 1 00.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 35 1 00 means on a Sub-Zero wine storage

Error code 35 1 00 on a Sub-Zero wine storage unit indicates an open circuit condition in the Zone 1 evaporator fan. An open circuit means the control board is detecting a break in the electrical continuity of the fan circuit, which prevents the fan motor from receiving power or completing its operating loop. The evaporator fan in Zone 1 is responsible for circulating air across the evaporator coil and distributing cooled air throughout that zone. When this fan fails to operate, the zone loses its ability to maintain consistent temperature, which directly threatens wine storage conditions.

The open circuit fault can originate at several points in the fan circuit. The fan motor windings themselves can develop an internal break, eliminating continuity through the motor. The wiring harness connecting the fan to the control board may have a damaged, corroded, or disconnected terminal. Connectors can loosen over time due to vibration or thermal cycling, creating intermittent or permanent open circuit conditions. The fan motor may also have a failed thermal protector that has opened under an overtemperature condition.

Diagnosing this code requires starting at the control board and the fan assembly itself. Technicians should inspect all wiring connectors in the Zone 1 fan circuit for signs of corrosion, looseness, or physical damage before condemning either the fan motor or the board. Continuity testing of the fan motor windings will confirm whether the motor itself is the source of the open circuit. If wiring and connectors check out, the control board's fan output circuit should be evaluated.

Source: manufacturer service documentation.

Common causes of 35 1 00

  1. 01

    Failed evaporator fan motor

    Part replacement

    The Zone 1 fan motor windings can develop an internal open circuit, causing a complete loss of continuity. Continuity testing across the motor terminals will confirm this failure.

  2. 02

    Disconnected or damaged wiring harness

    Wiring / connection

    Vibration and thermal cycling can loosen or disconnect the wiring connector between the fan and the control board. Inspect all connectors in the Zone 1 fan circuit for looseness, corrosion, or broken wires.

  3. 03

    Corroded or faulty connector terminals

    Wiring / connection

    Corrosion on the fan circuit connector terminals can create high resistance or a complete open in the circuit. Cleaning or replacing the connector may restore proper continuity.

  4. 04

    Open thermal protector in fan motor

    Part replacement

    The fan motor's internal thermal protector may have tripped or failed open due to overtemperature conditions. This will present as an open circuit even though the motor windings themselves may be intact.

  5. 05

    Control board fan output failure

    Part replacement

    If the wiring and fan motor both test correctly, the control board's output circuit for the Zone 1 fan may have failed. This is less common but should be evaluated after ruling out the fan and wiring.

See the test procedure for each cause

Frequently asked questions about 35 1 00

What does 35 1 00 mean on a Sub-Zero wine_storage?
Error code 35 1 00 indicates an open circuit condition in the Zone 1 evaporator fan circuit. The control board is detecting that electrical continuity through the fan is broken, which means the fan cannot run. This will cause Zone 1 to lose proper air circulation and temperature control. The fault can originate at the fan motor, the wiring harness, or the control board.
Can I fix error code 35 1 00 myself?
A knowledgeable DIYer can start by inspecting the Zone 1 fan wiring connectors for looseness or visible damage and reseating any disconnected terminals. However, continuity testing of the fan motor and evaluating the control board require a multimeter and familiarity with appliance wiring. If the fan motor or control board needs replacement, a qualified technician is recommended to ensure correct parts and safe reassembly.
Is error code 35 1 00 a safety risk?
This fault is not an immediate safety hazard to people, but it does pose a risk to the wine being stored. Without the Zone 1 evaporator fan operating, that zone cannot maintain stable temperature, which can damage wine over time. The issue should be addressed promptly to protect the contents of the unit.
Will resetting the unit clear error code 35 1 00?
A reset may temporarily clear the displayed code, but the fault will return if the underlying open circuit condition has not been corrected. The control board will detect the fan circuit failure again once it attempts to operate the fan. A reset should only be used as part of the diagnostic process, not as a fix.
How much does it cost to repair error code 35 1 00 on a Sub-Zero wine unit?
Repair costs vary depending on the root cause. If the fix is a reseated connector or a minor wiring repair, costs may be limited to a service call fee, typically in the range of $100 to $200. Replacing a fan motor generally adds $150 to $400 in parts and labor. A control board replacement is the most expensive scenario, often ranging from $400 to $900 or more depending on the specific model.

Related Sub-Zero wine storage codes

All Sub-Zero wine storage codes
View all 72 Sub-Zero wine storage codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass