mypros+
Error code reference

Sub-Zero Wine Storage Error Code 35 2 33

Zone 2 fan speed set too low; fan is running faster than its setting.

Sub-Zero codesSub-Zero wine storage codes

Zone 2 fan speed set too low; fan is running faster than its setting.

First step from the service manual

Verify fan not shorted.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 35 2 33.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 35 2 33 means on a Sub-Zero wine storage

Error code 35 2 33 on a Sub-Zero wine storage unit indicates a fan speed fault specific to Zone 2. The control board monitors the actual rotational speed of the evaporator or circulation fan in Zone 2 and compares it against the programmed speed setting. When the fan is detected running faster than its configured target speed, the unit logs this code. This type of discrepancy points to a feedback or control signal issue rather than a mechanical failure, since the fan is actively spinning but not being properly governed.

The most critical first diagnostic step is confirming that the fan motor or its wiring harness is not shorted. A short in the fan circuit can cause the control board to receive erratic or incorrect speed signals, leading the system to misread the fan's actual operating speed. A shorted winding in the fan motor can also cause runaway behavior where the motor operates outside its intended speed range. Testing the fan motor windings for continuity and checking the harness for any damaged insulation or pinched wires is essential before replacing any components.

If no short is found, the fault may lie in the fan speed control circuit, the fan motor itself, or the main control board. A failing control board may be sending an incorrect speed reference signal, causing a mismatch between the commanded and actual speed. In some cases, a fan motor with worn bearings or degraded internal components can behave erratically even without a detectable short. Systematic testing of the fan, its connector, and the board's output signals is needed to isolate the root cause.

Source: manufacturer service documentation.

Common causes of 35 2 33

  1. 01

    Shorted fan motor winding

    Part replacement

    A short within the Zone 2 fan motor can cause uncontrolled motor speed, bypassing the speed control signal from the board. Check motor winding resistance with a multimeter and look for values outside normal range or direct shorts to ground.

  2. 02

    Damaged or shorted wiring harness

    Wiring / connection

    Pinched, frayed, or shorted wires in the fan circuit can send erratic signals to the control board, causing false speed readings. Inspect the harness routing for contact with sharp edges or heat sources.

  3. 03

    Faulty fan speed control signal from the control board

    Part replacement

    If the main control board is outputting an incorrect speed reference voltage, the fan may run at an unregulated speed. This can be identified by measuring the control signal at the fan connector and comparing it to expected values.

  4. 04

    Failing fan motor

    Part replacement

    A fan motor with degraded internal components may operate erratically even without a measurable short, running above its commanded speed. If wiring and board outputs check out, the motor itself should be replaced.

  5. 05

    Loose or corroded fan connector

    Wiring / connection

    A poor connection at the fan motor connector can cause intermittent or incorrect feedback signals to the control board, triggering a speed fault. Inspect the connector pins for corrosion, looseness, or heat damage.

See the test procedure for each cause

Frequently asked questions about 35 2 33

What does 35 2 33 mean on a Sub-Zero wine_storage?
Error code 35 2 33 means the Zone 2 fan speed is set too low relative to how fast the fan is actually running. The control system detected that the fan is spinning faster than its programmed target speed. This points to a fault in the fan motor, its wiring, or the control board's speed regulation circuit. The first step in diagnosing this code is checking whether the fan or its wiring is shorted.
Can I fix error code 35 2 33 myself?
Some preliminary checks, such as inspecting the fan wiring harness for visible damage or loose connectors, can be done by a knowledgeable DIYer. However, testing motor windings, measuring control signals, and replacing the control board require electrical diagnostic skills and appropriate tools. If you are not comfortable working with appliance electronics, it is best to contact a qualified technician.
Is error code 35 2 33 a safety concern for my wine storage unit?
A fan running above its set speed in Zone 2 can disrupt the precise temperature control that wine storage requires, potentially affecting your wine over time. While this fault is unlikely to create an immediate safety hazard, a shorted fan motor or wiring could theoretically pose an electrical risk if left unaddressed. Prompt diagnosis is recommended to protect both your unit and its contents.
How much does it cost to repair error code 35 2 33 on a Sub-Zero wine unit?
Repair costs depend on the root cause. If only wiring or a connector needs attention, costs may be relatively low, typically in the range of $100 to $250 for a service call and labor. A replacement fan motor typically adds $150 to $400 in parts. If the main control board is at fault, parts and labor combined can range from $400 to $900 or more depending on the specific model.
Will resetting the unit clear error code 35 2 33?
Resetting the unit may temporarily clear the code from the display, but if the underlying fault in the fan motor, wiring, or control circuit is still present, the code will return. A reset does not repair a shorted motor or a defective control board. The fault should be diagnosed and corrected before relying on the unit to maintain proper wine storage conditions.

Related Sub-Zero wine storage codes

All Sub-Zero wine storage codes
View all 72 Sub-Zero wine storage codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass