mypros+
Error code reference

Whirlpool Range Error Code F5

Door and latch switches do not agree (door switch open indicating open door and latch switch closed indicating locked door) / Door latch not…

Whirlpool codesWhirlpool range codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F5 error code actually means

The F5 error means your oven's control board is having trouble reading whether the oven door is open or closed. A small sensor called a door switch is supposed to constantly report the door's position, but the board is receiving a confusing or missing signal from it. This is usually caused by a faulty door switch or a loose wire connecting it to the control board.

Diagnostic procedure

The full F5 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
If door latched: Disconnect power, check wires and connectors from control to door switch and back. Replace door switch if wiring OK. Reapply power, press CANCEL to clear F5, program and start Clean mode, observe 1 minute. If door not latched: Disconnect power, check wires and connectors from control to latch switch and back, then repeat for door switch. Measure door switch (door open = switch open on small low voltage terminals). Measure latch switch (unlatch = switch open, oven light contacts closed). If failure remains, disconnect power and replace control.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F5 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F5

Ranked by how often they cause this code
  1. 1Failed door switch
  2. 2Loose or damaged wiring to the door switch
  3. 3Door switch misaligned due to hinge or door damage
  4. 4Faulty control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F5

What does F5 mean on a Whirlpool range?
F5 on a Whirlpool range means the control board is receiving an inconsistent signal from the door switch. The door switch tells the oven whether the door is open or closed. When the signal is missing or unreliable, the board logs F5. Start by opening and closing the door to check whether the oven light responds normally.
Is it safe to use my Whirlpool range with an F5 code active?
Basic cooktop burner use is generally possible, but you should avoid using the self-clean cycle while F5 is active. The self-clean function relies on accurate door position data to engage the door lock safely. Running self-clean without a reliable door signal creates a safety risk. Baking and broiling may also be affected depending on how the control board handles the fault.
Can a bad wiring connection cause the F5 code on a Whirlpool range?
Yes, a loose or damaged wiring connector between the door switch and the control board can produce the F5 code even if the switch itself is functioning. Before ordering a replacement switch, unplug the range and inspect the wire harness connector at the door switch for corrosion, looseness, or broken terminals. Reconnecting or repairing the connector may clear the code without requiring a new part.
How do I fix the F5 error code on my Whirlpool range?
Open and close the oven door and watch the oven light. If the light does not turn on when the door opens or off when it closes, the door switch needs to be replaced. Before replacing the switch, also inspect the wiring connector at the switch for looseness or visible damage. If the switch and wiring look fine, check whether the door is properly aligned and making full contact with the switch actuator.
How much does it cost to fix the F5 error on a Whirlpool range?
A replacement door switch for a Whirlpool range typically costs between $15 and $40 for the part. If you replace it yourself, that is the total cost. A repair technician will add a service call fee and labor, bringing the total to roughly $100 to $200 depending on your area. Door switch replacement is a relatively accessible DIY repair since the switch is usually located near the door frame and secured with one or two screws.

Related Whirlpool range error codes

All Whirlpool range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass