mypros+
Error code reference

Whirlpool Washer Error Code d6

EEPROM error (AccuTrac display equivalent for F01).

Whirlpool codesWhirlpool washer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the d6 error code actually means

The d6 code means your washer's main computer board is having trouble accessing its internal memory, which stores the settings it needs to run properly. Think of it like a computer that can't read its own hard drive. Unplugging the washer for two minutes often clears the issue if it was caused by a power glitch, but if the code comes back, the control board likely needs to be replaced.

Diagnostic procedure

The full d6 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Unplug washer or disconnect power for two minutes.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock d6 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of d6

Ranked by how often they cause this code
  1. 1Transient power disruption
  2. 2Failed or corrupted EEPROM on the control board
  3. 3Faulty main control board
  4. 4Voltage spike or power surge

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about d6

What does d6 mean on a Whirlpool washer?
The d6 code on a Whirlpool washer with an AccuTrac display indicates an EEPROM error, equivalent to the F01 fault code on other Whirlpool models. It means the main control board is unable to properly access or read its internal memory chip. This memory stores the operating parameters the washer needs to run, so when it fails, the machine cannot function normally.
Will resetting the washer clear the d6 code?
A power reset by unplugging the washer for two minutes will clear the d6 code if it was caused by a temporary power disruption or corrupted write cycle. However, if the EEPROM or control board has permanently failed, the code will return after the reset. A reset that does not hold is a strong indicator that the control board needs to be replaced.
How much does it cost to fix a d6 error on a Whirlpool washer?
If the error clears with a power reset, there is no parts cost. If the main control board requires replacement, parts alone typically range from $150 to $350 depending on the specific model, with professional labor adding another $100 to $200 in most markets. Getting a repair estimate before committing can help you compare the cost against the value of the appliance.
Can I fix the d6 error myself?
The first step is to unplug the washer or disconnect power for two minutes, then restore power and see if the code clears. If that resolves it, no further action is needed. If the code returns, the repair involves replacing the main control board, which is a job many experienced DIYers can handle but requires care when working with electronic components.
Is it safe to use my Whirlpool washer when d6 is displayed?
You should not attempt to run the washer while the d6 code is active. The error indicates the control board cannot access its stored operating data, which means the machine may not run cycles correctly or safely. Resolve the fault before resuming laundry use.

Related Whirlpool washer error codes

All Whirlpool washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass