mypros+
Model reference

Whirlpool CHW9900VQ0

Washer

4 documents43 error codes22 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10194215A (FR)16 pg
    Covers this model
  • Whirlpool Commercial Washer CHW9900VQ1 Tech Sheet16 pg
    Covers this model
  • Tech Sheet - W10192827A16 pg
    Covers this model

Installation Guide

  • Installation Instructions32 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool CHW9900VQ0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (43)

CodeMeaning
d10MCU failured11Motor Control Unit errord12Drive motor tachometer error (AccuTrac display equivalent for F25).d13Coin 2 sensor errord14Pump drive system error (AccuTrac display equivalent for F33).d15Load inside drum during cleaning washer cycle (AccuTrac display equivalent for…d16Generation 2 debit card reader errord17Door lock error (AccuTrac display equivalent for F22).d18Dispenser system error (AccuTrac display equivalent for F30).d19Door unlock error (AccuTrac display equivalent for F29).d20Serial communication error (AccuTrac display equivalent for F28).d21Overflow condition (AccuTrac display equivalent for F27).d22Central Control Unit heartbeat failure (AccuTrac display equivalent for F70).d23User Interface heartbeat failure (AccuTrac display equivalent for F71).d24Water temperature sensor error (AccuTrac display equivalent for F24).d3UI EEPROM error or UIC EEPROM error (AccuTrac display equivalent for F73/F74).d4Door switch errord5Coin 1 sensor errord6EEPROM error (AccuTrac display equivalent for F01).d7No water detected entering machine or pressure switch trip not detected…d8Long drain (AccuTrac display equivalent for F21).d9Low voltage detection errorF01EEPROM communication error between the Central Control Unit (CCU) and the CCU…F11Drive pump source not activating (pump error).F20No water entry detected or no pressure switch activation after 6 minutes.F21Excessive drain timeF22Door lock errorF24Water temperature sensor errorF25Drive motor tachometer errorF26Door switch error
View all 43 error codes
F27Overflow conditionF28Serial communication error between the Central Control Unit (CCU) and the Motor…F29Door unlock errorF30Dispenser system errorF31MCU (Motor Control Unit) failureF33Pump drive system errorF34Laundry detected inside drum during washer cleaning cycle (alternate display…F70Central Control Unit heartbeat signal failureF71User interface heartbeat signal failureF73User interface EEPROM communication error between UI and UI EEPROM.F74User interface controller EEPROM CRC read error.rLLaundry detected inside drum during washer cleaning cycle (detected by weight).SdSlow drain indicator

Service modes (22)

  • Clean Washer Cycle (Diagnostic)["Enter Diagnostic Flashing Mode (entire display flashing).","Press the COLORS/DELICATES key pad."]
  • Code Display Mode["This mode can be accessed only when the washer is in error state.","Open the service door.","The…
  • Control Set-Up Mode (PD/PS Models)["Insert access door key, turn, and lift to remove access door.","The temperature key pads and the…
  • Control Set-Up Mode (PR Models)["Insert a manual set-up card (supplied by the reader manufacturer) into the card slot.","If a…
  • Cycle Credit["Enter Diagnostic Flashing Mode (entire display flashing).","Press the HOT key pad (CC will…
  • Diagnostic Mode - Code Display Sub-mode["This mode is accessed only when the washer is in an error condition.","Open the service…
  • Diagnostic Mode - Flashing/Blinking Sub-mode["First press 'Start Operating Set-up' button.","Then press COLD button for 1 second while one of…
  • Diagnostic Test - Credit a Cycle["Enter Flashing/Blinking sub-mode.","While entire display is flashing, press HOT button."]
  • Diagnostic Test - History Overview Test Program["Enter Flashing/Blinking sub-mode.","While entire display is flashing, press WARM button."]
  • Diagnostic Test - Manual Overview Test Program["Enter Flashing/Blinking sub-mode.","While entire display is flashing, press COTTON/WHITES…
  • Diagnostic Test - Quick Spin Program["Enter Flashing/Blinking sub-mode.","While entire display is flashing, press PERM PRESS button."]
  • Diagnostic Test - Washer Cleaning Program["Enter Flashing/Blinking sub-mode.","While entire display is flashing, press COLORS/DELICATES…
  • Help Mode["For manual communication
  • Help Mode (DA Communication Established)["Open the service door.","The message dAS will appear in the display.","Press the HOT key.","Press…
  • Help Mode (Manual Communication)["Open the service door.","Press the WARM key until the special pricing option mode (2.XX) is on…
  • History Overview Test Program["Enter Diagnostic Flashing Mode (entire display flashing).","Press the WARM key pad."]
  • Manual Load Test Cycle (Manual Overview Test Program)["Enter Diagnostic Flashing Mode (entire display flashing).","Press the COTTON/WHITES key pad."]
  • Quick Spin Cycle["Enter Diagnostic Flashing Mode (entire display flashing).","Press the PERM PRESS key pad."]
  • Set-up Mode (PD/PS Models)["Insert access door key, turn, and lift to remove access door.","The temperature key pads and…
  • Set-up Mode (PR Models)["Insert a manual set-up card (supplied by the reader manufacturer) into the card slot.","If a…
  • Setup/Configuration Mode (Manual Communication)["PD/PS models
  • Washer Diagnostic Mode (Flashing Mode)["First enter Start Operating Set-Up (set-up mode).","Press and hold the COLD key pad for 1 second…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax