mypros+
Model reference

Amana 109-2E

Air Conditioner

63 error codes29 service modes
MyPros+ Max

Diagnose your Amana 109-2E.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (63)

CodeMeaning
F0 E7Control board recognized line voltage below 90 VAC.F0E2Oversuds condition detectedF0E3Overload detectedF0E4Spin limited by water temperatureF0E5Off balance load condition detected.F0E7Load detected when running Clean Washer cycle.F0E8Water ring faultF0E9Off balance pauseF1 E1ACU (Appliance Control Unit) fault.F1 E7ACU voltage input fault.F10E1Freezer Compartment (FC) Fan failure.F10E11Refrigerator Compartment (RC) Damper failure.F1E1Indicates a CCU (Cycle Control Unit) problem.F2 E1Lower dryer keypad is sensed pressed for 60 seconds (stuck key).F2 E2Upper dryer keypad is sensed pressed for 60 seconds (stuck key).F2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatchF2E2HMI disconnected from the ACU.F3E1Outlet thermistor is open; temperature drops below 18°F (>50k ohms).F3E2Outlet thermistor has shorted; temperature above 250°F (<500 ohms).F3E3Inlet water temperature faultF3E4Inlet thermistor is shorted; temperature above 391°F (< 328 ohms).F3E5Compressor and outlet thermistors are open; will occur if the P14 connector is…F3E6Moisture sensor strip is openF3E7Moisture sensor strip has shortedF3E8Compressor sensor is open; this fault code will stop the dryer.F3E9Compressor sensor has shorted; this fault code will stop the dryer.F4E1No voltage detected at the heater relay; appears only in Diagnostic Test Mode.F4E2Refrigeration Compartment Evaporator Heater failure.F4E3Restricted/low air flow that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at the CCU.
View all 63 error codes
F5 E1Lower dryer door circuit error.F5 E6Upper dryer door circuit error.F5E1Lid switch faultF5E3Lid lock will not unlockF5E4Lid not opened between cyclesF6E1Communication between the CCU and UI has not been detected (UI to CCU…F6E2Communication between the CCU and UI has not been detected (CCU to UI…F7 E6Lower dryer motor circuit error.F7 E7Upper dryer motor circuit error.F7 E8Lower dryer motor sense errorF7 E9Upper dryer motor sense errorF7E1Tachometer missing or wrong signalF7E3Basket engaged during washF7E4Basket re-engagement failureF7E6Motor circuit openF7E7Motor unable to reach target RPM.F8E1Long fillF8E2Dispenser system failureF8E3Overflow or flood conditionF8E5Exhaust air temperature detection failure.F8E6Water hazardF9E1Drain system errorFAE1Refrigeration Compartment or Main Evaporator Fan failure.FAEBDamper 1 (RC Damper) failure.FC E1Model/Serial number not programmed into control.FC E4USB stick failure (USB full, not detected, or not accessible).FC E5Software uploaded from USB stick does not match the model number of the machine.FP E1Coin 1 circuit errorFP E2Coin 2 circuit errorFP E3Card reader communication error.L2Low L2 voltage (less than 50V) detected at the CCU.LFLint filter has been removed from running position.PFPower failure occurred while the dryer was running.

Service modes (29)

  • Component ActivationEnter Service Mode, navigate to Service Diagnostics, select Component Activation
  • Component Activation Mode["Enter Service Mode.","Navigate to Service Diagnostics.","Select Component Activation.","Use…
  • Customer-Focused Dryness Level Adjustment["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS LEVEL button…
  • diagnostic["Plug in microwave oven or reconnect power.","Press Cancel button to reach Standby mode (colon ':'…
  • Diagnostic CycleEnter Service Mode, navigate to Service Diagnostics, select Diagnostic Cycle.
  • Diagnostic Mode["Enter Setup Mode first.","While in any of the set-up codes 1 through 6 (or while dAS displays if…
  • DLMS Calibration CycleEnter Service Mode, navigate to Factory Diagnostics, select DLMS Calibration Cycle.
  • Error Code / Show Fault ModePress and Hold Refrigerator Temperature button + Cubed Ice buttons for 5 seconds.
  • Error Code Display ModePress and Hold Refrigerator Temperature button + Cubed Ice buttons for 5 seconds.
  • Fault HistoryEnter Service Mode, navigate to Fault History
  • Fault ResetFrom Service Test Mode, press 1st button for 5 seconds to reset the faults.
  • Help Mode["Enter Setup Mode first.","While in special pricing option step 2.XX (or while dAS displays if…
  • HMI TestEnter Service Mode, navigate to Service Diagnostics, select HMI Test
  • Install Diagnostics["Activate Service Diagnostic Mode first (see Service Diagnostic Mode entry).","Ensure all of step…
  • Loads Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Within 5 seconds
  • Manual Control ModeFrom the Service Test Mode main menu, press the selected first button for a short duration to enter…
  • Model/Serial Number Menu["Enter Help Mode.","While on the S0 screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • Sensor FeedbackEnter Service Mode, navigate to Service Diagnostics, select Sensor Feedback
  • Sensor Feedback Mode["Enter Service Mode.","Navigate to Service Diagnostics.","Select Sensor Feedback.","Use Left/Right…
  • Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Select any three buttons…
  • Service Mode1. Ensure washer is in standby mode (plugged in with all indicators off). 2. Select any three…
  • Service Test Mode1. Press and release any 3 keypad buttons, three times in sequence
  • Setup Mode["Stacked PD Models
  • Show Fault ModeFrom Service Test Mode, press 1st button for a short duration.
  • Software Version Display["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…
  • Software Version Display ModeFrom Service Test Mode, press 1st button for 3 seconds.
  • USB Menu["Enter Help Mode.","While on the USB screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • User Interface Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
  • User Interface/Control System Test1. Activate Service Diagnostic Mode. 2. Press and release the 1st button used to activate Service…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana air conditioner models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass