mypros+
Model reference

Amana 210-3B

Air Conditioner

4 documents73 error codes13 service modes

Available documentation

Service Manual

  • Service Manual - RS410000342 pg
    Covers this model
  • Service Manual - RS410000743 pg
    Covers this model
  • Service Manual - RS411000233 pg
    Covers this model
  • Service Manual - RS410000845 pg
    Covers this model
MyPros+ Max

Diagnose your Amana 210-3B.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (73)

CodeMeaning
:Flashing colon on display indicates a power failure has occurred.1-1Control detected K2 pilot relay stuck closed.1-2Control software issue; all LEDs are on due to software or hardware…10-1Dispenser electrical problem; loose connection in dispenser circuit and/or open…10-3Drying fan error; loose connection in fan circuit and/or open fan motor.2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface cannot communicate with main control; loose user interface…3-1Open connector or component in Temperature Sensing circuit (open or faulty…3-2Shorted connection or component in Temperature Sensing circuit, or incoming…3-3OWI (Optical Water Indicator) failed calibration.4-3Wash motor not running due to loose connection in motor circuit and/or faulty…5-1Door switch stuck open; loose connection in door switch circuit and/or door…5-2Door switch stuck closed; control detected door switch did not open between…6-1Low or no water reaching dishwasher (mechanical problem).6-2Fill valve electrical problem; loose connection in fill valve circuit and/or…6-3Suds or air detected in pump.6-4Overfill float switch stuck in overfill position and/or dishwasher not level.6-6Incoming water too cool (under 84°F / 29°C).6-7Flowmeter disconnected or damaged.6-8Water softener regeneration valve electrical problem (loose connection in regen…7-1No heat; control disabled heater due to detected water heating problem.7-2Heater stuck on; heater drive circuit on the control failed.8-1Slow drain due to obstructed drain hose or path.8-2Drain motor electrical problem; loose connection in drain motor circuit and/or…8-3Drain motor stuck on; drain motor drive circuit on the control failed.F0No error present.F0 E0No error(s) found (Good).F1 E0EEPROM communications error.F1 E1EEPROM checksum failure.F1 E2UL A/D error(s).
View all 73 error codes
F1-E0EEPROM communications failure.F1-E1EEPROM checksum failure.F1-E2UL A/D error(s).F10Display error.F1E1ACU detects a feedback signal different than expected, an input signal out of…F1E2Motor failure including over current, DC bus over/under voltage, locked rotor…F2Keyboard (membrane switch) failure.F2 E0Shorted key / Stuck key.F2 E1Keytail unplugged.F2-E0Shorted key detected.F2-E1Keytail unplugged from electronic oven control.F2KKey or foil pressed more than 1 minute.F2TTouch panel pressed more than 1 minute.F3 E0Oven sensor opened.F3 E1Oven sensor shorted.F3 E2BAKE/BROIL range over temperature.F3 E3CLEAN range over temperature.F3-E0Oven temperature sensor open circuit.F3-E1Oven temperature sensor shorted.F3-E2Bake range over temperature condition.F3-E3Clean range over temperature condition.F3E1Indicates a problem in the Front Thermistor circuit.F3E3Indicates a problem in the Hot thermistor circuit.F3HHumidity sensor failure.F3TTemperature sensor failure.F4E7Indicates a problem in the supply voltage to the machine.F5 E0Door latch and switches do not agree.F5 E1Door latch not operating.F5 E2Latch error during CLEAN.F5-E0Door and latch switches do not agree.F5-E1Door lock solenoid not operating or latch switch failure.F5-E2Latch during CLEAN error.F5E1Indicates a short in the Door Switch circuit.F6E1Communication failure between the HMI and the ACU.F6E2Communication failure between the HMI and the ACU.F6E3ACU does not receive data from the Motor MCU.F7Power to magnetron interrupted.F9CE2PROM CheckSum error.F9EE2PROM empty.F9E2Indicates the drain system has a failure.F9ME2PROM missing.F9WE2PROM write error.PFPower failure has occurred.

Service modes (13)

  • Customer Cycle Rapid Advance["Start a customer cycle.","Press HIGH TEMP
  • Last error code recallPress and hold CANCEL/OFF key for 5 seconds until last error code is displayed.
  • Oven Temperature Calibration1. Press and hold the BAKE keypad for 5 seconds. The current offset (if any) is shown in the…
  • Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
  • Self-Diagnostic Test Mode["Press and hold the OFF/CANCEL button while opening the door.","While still holding the OFF/CANCEL…
  • Service Diagnostic Mode / Service Test Cycle["Open and close the dryer door (door must be closed).","Ensure dryer is in standby mode (plugged…
  • Service Diagnostics Cycle1
  • Temperature Adjustment (Calibration)Press and hold BAKE pad for 5 seconds
  • Temperature Calibration AdjustmentPress and hold BAKE pad for 5 seconds. Current offset is shown in display (CAL shown in 4-digit…
  • Test mode (diagnostic)Within 60 seconds of power up, simultaneously hold down the BAKE and CLOCK keys for 5 seconds
  • Test mode readoutAfter entering test mode, press the arrow down key to cycle through
  • Touch Panel and Microcomputer Board Test (Self-Diagnostic)["Press the clock key.","Press keys 1, 2, and 3 on the keyboard.","Touch AM/PM on the touch screen…
  • Touch Panel and Microcomputer Board Test Mode (Self-Diagnostic)["Press the CLOCK key.","Touch 'Hours' on the touch screen and set hours to '1'.","Touch 'Minutes'…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana air conditioner models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass