mypros+
Model reference

Amana CRH5-1/P55200-25C

Air Conditioner

1 document47 error codes21 service modes

Available documentation

Tech Tip

  • Instruction Sheet4 pg
    Covers this model
MyPros+ Max

Diagnose your Amana CRH5-1/P55200-25C.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (47)

CodeMeaning
F0 E0No fault codes stored in memory.F0 E2Over suds condition detectedF0 E4High water temperature detected during rinse cycle (105°F or higher).F0 E5Off balance load detected.F0E0No fault codes stored in memory.F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected during rinse cycle (105°F or higher).F0E5Off balance load detected.F1Interlock switch(es) closed when door is openF1 E1Main control fault.F1 E2Motor control faultF1E1Main control fault.F1E2Motor control fault on the main control board.F2Gas sensor is defective or sensor wires are not properly connected.F2 E1Stuck keyF2 E3Mismatch of Main Control and UIF2E1Stuck key detected; one or more keys on the User Interface were actuated for 15…F2E2Mismatch of main control and user interface; UI identification does not match…F2E3Stuck key detected (alternate error number for stuck key fault).F3 E1Pressure sensor faultF3 E2Inlet water temperature faultF3E1Pressure sensor fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected open or shorted.F5 E1Lid switch faultF5 E2Lid lock faultF5 E3Lid unlock faultF5 E4Lid not opened between cyclesF5E1Lid switch faultF5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…
View all 47 error codes
F5E4Lid not opened between cycles; user presses START after several consecutive…F7 E1Basket speed sensor faultF7 E5Shifter faultF7 E6Motor faultF7 E7Motor unable to reach target RPMF7E1Basket speed sensor fault; main control cannot determine speed of basket or…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; open clockwise or counterclockwise circuit of the motor.F7E7Motor unable to reach target RPM; basket speed sensor detects target RPM was…F8 E1No fill / long fillF8 E3Overflow conditionF8 E5Hot and cold water supply hoses are reversed.F8E1No fill / long fill; water level does not change for a period of time or water…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F9 E1Long drainF9E1Long drain; water level does not change after drain pump is on for 10 minutes.

Service modes (21)

  • Automatic Test Mode["Enter Diagnostic Test Mode.","Turn cycle selector knob until Spin LED is On (display shows '02'…
  • automatic_test["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Spin LED…
  • calibration["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Rinse LED…
  • Calibration Mode["Enter Diagnostic Test Mode.","Turn cycle selector knob until Rinse LED is On (display shows '04'…
  • diagnostic["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Diagnostic Test Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Fault Code Display Mode["Enter Diagnostic Test Mode.","Turn cycle selector knob until Done LED is On (display shows '01'…
  • fault_code_display["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Done LED…
  • Manual Test Mode["Enter Diagnostic Test Mode.","Turn cycle selector knob until Spin & Done LEDs are On (display…
  • manual_test["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Spin &…
  • Sales Demo Mode["Activate diagnostic test mode.","Turn cycle selector knob until Rinse & Done LEDs are On and…
  • Sales Demonstration Mode
  • Service Diagnostic Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Software Version Display Mode["Enter Diagnostic Test Mode.","Turn cycle selector knob until Rinse, Spin, and Done LEDs are On…
  • sw_version_display["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Rinse…
  • Tachometer Verification Mode["Enter Diagnostic Test Mode.","Turn cycle selector knob until Wash and Done LEDs are On (display…
  • tachometer_verification["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Wash and…
  • Touch Panel Continuity Test / Diagnostic["Unplug the microwave oven power supply cord.","Open the oven door.","Plug the power cord back…
  • UI Test Mode["Enter Diagnostic Test Mode.","Turn cycle selector knob until Rinse & Spin LEDs are On (display…
  • ui_test["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Rinse &…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana air conditioner models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax