mypros+
Model reference

Amana GHE200M-R5/P96596-13F

Furnace

2 documents23 error codes23 service modes

Available documentation

Installation Guide

  • Installation Instructions7 pg
    Covers this model
  • Installation Instructions52 pg
    Covers this model
MyPros+ Max

Diagnose your Amana GHE200M-R5/P96596-13F.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (23)

CodeMeaning
d13The Coin 2 sensor is detected as blocked; coin vault may be full or sensor may…d16No communication from Generation 2 debit card reader.d5The Coin 1 sensor is detected as blocked; coin vault may be full of money or…d9Incoming voltage detected below 90 VAC.F01Indicates a main control fault.F03Main control detects an out of range pressure signal from the pressure sensor.F07Main control cannot determine position of shifter.F11Indicates a fault of the motor control section of the main control.F20Water level does not change for a period of time or water is present but main…F21Water level does not change after the drain pump is on for 10 minutes (long…F22Lid lock has not moved into locked position or motor cannot be powered; lid not…F24Inlet water temperature fault; inlet thermistor is detected to be open or…F25Main control cannot determine speed of basket, or speed changes too quickly…F26Lid is in locked state, but lid switch is open; main control cannot detect lid…F27Main control senses a water level that exceeds the washer's capacity (overflow…F29Lid lock has not moved into unlocked position or motor cannot be powered.F32No fill detected; water level does not change for a period of time.F70Communication failure between CCU and UI; electrical connection between CCU and…F71Communication failure between CCU and UI; electrical connection between CCU and…F73The User Interface identification does not match the expected value in the Main…F74The User Interface identification does not match the expected value in the Main…F77Off balance load detected.PFPower failure indication; blinks in the display after a power outage longer…

Service modes (23)

  • Automatic Function TestWith door latched, press key pads in the following sequence within 10 seconds
  • Calibration Cycle (P-05)Access Service Diagnostic Test Modes, press MIXED until P-05 is displayed, press START.
  • Clean Washer Cycle (P-12)Access Service Diagnostic Test Modes, press MIXED until P-12 is displayed, press START.
  • Clear Errors (P-01)Access Service Diagnostic Test Modes, display shows P-01, press START to clear active error code.
  • Cycle Credit (P-02)Access Service Diagnostic Test Modes, press MIXED until P-02 is displayed, press START.
  • Drain & Spin Cycle (P-06)Access Service Diagnostic Test Modes, press MIXED until P-06 is displayed, press START.
  • Help ModePerform step 1 of Activating Service Diagnostic Test Modes, then press MIXED until the 2.xx code is…
  • Manual Function TestWith door latched, press key pads in the following sequence within 10 seconds
  • Manual Overview Test (P-04)Access Service Diagnostic Test Modes, press MIXED until P-04 is displayed, press START
  • P-01 Clear Errors["Access Service Diagnostic Test Modes.","Display shows 'P-01'.","Press START to clear an active…
  • P-02 Cycle Credit["Access Service Diagnostic Test Modes.","Press NORMAL to step to 'P-02'.","Press START to provide…
  • P-03 Service Diagnostic["Access Service Diagnostic Test Modes.","Press NORMAL to step to 'P-03'.","Press START to initiate…
  • P-04 Manual Diagnostic["Access Service Diagnostic Test Modes.","Press NORMAL to step to 'P-04'.","Press START to initiate…
  • P-05 Calibration Cycle["Access Service Diagnostic Test Modes.","Press NORMAL to step to 'P-05'.","Press START to initiate…
  • P-07 UI Diagnostics["Access Service Diagnostic Test Modes.","Press NORMAL to step to 'P-07'.","Press START to start UI…
  • P-09 Tachometer Verification["Access Service Diagnostic Test Modes.","Press NORMAL to step to 'P-09'.","Press START to start…
  • P-12 Clean Washer Cycle["Access Service Diagnostic Test Modes.","Press NORMAL to step to 'P-12'.","Press START to start…
  • Quick Overview Test (P-03)Access Service Diagnostic Test Modes, press MIXED until P-03 is displayed, press START.
  • Service Diagnostic Test Modes1
  • Service Diagnostic Test Modes (entry)["For coin (PD) models
  • Tachometer Verification (P-09)Access Service Diagnostic Test Modes, press MIXED until P-09 is displayed, press START
  • Technician Service Access Code (PR Free Vend models only)Press the POWERWASH, EXTRA RINSE, TEMPERATURE, and DELICATES key pads within 10 seconds.
  • UI Diagnostics (P-07)Access Service Diagnostic Test Modes, press MIXED until P-07 is displayed, press START

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass