mypros+
Model reference

Amana OH-96-3

Furnace

8 documents46 error codes10 service modes

Available documentation

Service Manual

  • Pro Line™ & Commercial Blender Service Manual44 pg
    Covers this model
  • Job Aid - Outdoor Gas Grill (KAC-52)68 pg
    Covers this model

Installation Guide

  • Installation Instructions8 pg
    Covers this model
  • Instrucciones de instalacion32 pg
    Covers this model
  • Installation Instructions24 pg
    Covers this model
  • Installation Instructions88 pg
    Covers this model
  • Installation Instructions64 pg
    Covers this model
  • Installation Instructions140 pg
    Covers this model
MyPros+ Max

Diagnose your Amana OH-96-3.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (46)

CodeMeaning
:Flashing colon indicates a power failure has occurred.d13Coin 2 error; coin 2 detector detects that the coin slot is obstructed for 8…d9Low voltage detection error; input voltage detected below 90 VAC for 8 seconds.F0 E0No fault found.F01Communication error in the Central Control Unit (CCU); the pump drive in the…F1 E2Lost communication with power board.F1 E3Configuration jumper change; freestand, electric switches or P3 pins 1 to 5…F1 E4Oven sensor not calibrated.F1 E5Meat probe not calibrated.F1 E6Display board EPROM access failure.F1 E7Power board EPROM access failure.F1 E8Improper keypad feedback from power board supply lift.F1 E9Unstable keyboard gain.F1 EAExceeded stack warning level.F11Motor Control Unit (MCU) malfunction, possibly due to repeated under-voltage or…F1E4Microwave ACU PCBA failure.F2Touch panel failure.F2 E0User is cleaning too long or keypad is disconnected.F2 E1Cancel key invalid.F2 E3Key held down too long or keyboard short or spill on switch surface.F20No water entry detected; first pressure switch level not reached within 6…F21Excessive drain time; drain operation exceeds 8 minutes without reaching the…F22Door lock error; after multiple lock attempts and customer intervention, the…F24Water temperature sensor value out of range (-5°C to 103°C / 23°F to 217°F).F25Tachometer error; the MCU is unable to correctly detect motor speed, causing…F26Door switch error; the door switch circuit remains open for 5 seconds while the…F27Overflow condition; the overflow contact of the pressure switch is closed for…F28Communication failure between Central Control Unit (CCU) and Motor Control Unit…F29Door unlock error; after 6 attempts the door does not unlock.F2E1Stuck key failure.
View all 46 error codes
F3 E0Oven sensor open circuit.F3 E3Shorted oven sensor.F3 E4Oven temperature too high (runaway condition).F34Load detected in washer during the Clean Washer cycle.F4 E0Meat probe shorted (less than 1500 ohms).F4E4Humidity sensor error.F5 E1Self clean latch not locking.F5 E5Self clean temperature not achieved after 30 minutes.F5 E7Door unlocked but will not unlatch during clean cycle.F7 E0Invalid latch switch reading.F7 E1Invalid door switch reading.F70Communication failure between Central Control Unit (CCU) and User Interface…F8E5Exhaust air temperature detection failure.NTC OPEN, CALL FOR SERVICEHF NTC thermistor is open.NTC SHORT, CALL FOR SERVICEHF NTC thermistor is shorted.PFPower failure occurred (not a failure mode).

Service modes (10)

  • Diagnostic Mode (Blink Mode)["Enter Setup/Programming mode first.","Press and hold the COLD button for 2 seconds when setup…
  • Diagnostic Test Mode["Plug in microwave oven or reconnect power.","Press CANCEL to enter standby (colon ':'…
  • Diagnostics / Test Mode["Plug in microwave oven or reconnect power.","Press CANCEL button to reach Standby (colon ':'…
  • End of Service Test Sequence (Convection Units)["Connect unit to power, set power ON and wait until CONTROL LOCK clears and display shows PF…
  • End of Service Test Sequence (Non-Convection Units)["Connect unit to power, set power ON and wait until CONTROL LOCK clears and display shows PF…
  • Help Mode["Enter Setup/Programming mode.","Press WARM button until setup code 2.XX is displayed.","Press HOT…
  • Service Access Code Entry["Door must be open if washer is not in fault mode.","Press the upper left button.","Press the…
  • Setup/Programming Mode (Model 9050)["Insert key into access door, turn and lift to remove the access door."]
  • Setup/Programming Mode (Model 9060 via connector)["Disconnect power from the washer.","Open the console and disconnect connector AA1.","Close the…
  • Touch Panel and PCBA Self-Diagnostic Test Mode["Press and hold the STOP/CLEAR button while opening the door.","While still holding the STOP/CLEAR…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass