mypros+
Model reference

Amana OL-100/P96234-1F

Furnace

5 documents69 error codes12 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10136477 - Rev A_W101364778 pg
    Covers this model
  • Tech Sheet - W10268751 - Rev A_W1026875110 pg
    Covers this model
  • W10751162A.fm12 pg
    Covers this model
  • Tech Sheet - 820601020 pg
    Covers this model
  • Tech Sheet - 82058778 pg
    Covers this model
MyPros+ Max

Diagnose your Amana OL-100/P96234-1F.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (69)

CodeMeaning
:Flashing colon indicates a power failure has occurred.1-1Control function error1-2Control function error10-1Other10-2Other10-3Other2-1User Interface2-2User Interface3-1Thermistor/OWI3-2Thermistor/OWI3-3Thermistor/OWI4-2Wash Motor4-3Wash motor not running4-4Wash Motor5-1Door Switch5-2Door Switch6-1Inlet Water6-2Inlet Water6-3Inlet Water6-4Inlet Water6-6Inlet Water6-7Flowmeter error6-8Inlet Water7-1Heating7-2Heating8-1Draining8-2Draining8-3Draining8-4Draining9-1Diverter
View all 69 error codes
9-2Diverter9-3Diverter9-4DiverterF1-E1Control detected K2 pilot relay stuck closed.F1-E2Damaged or corrupted memory on control board; incompatible software components…F10-E1Dispenser electrical problem; loose connection in dispenser circuit and/or open…F10-E3Drying fan error; loose connection in fan circuit and/or open fan motor.F1E1Primary control failure indicating the machine control electronics has failed.F2Touch panel failure.F2-E1Control detected stuck key(s) in keypad or keypad connection.F2-E2User interface cannot communicate with main control; loose user interface…F2E1Stuck button or user interface mismatch; this fault code will ONLY appear when…F3-E1Open connector or component in temperature sensing circuit; open or faulty…F3-E2Incoming water temperature above 167°F (75°C), or shorted connection/component…F3-E3OWI calibration failure; dirty water backs into dishwasher after draining or…F3E1Exhaust thermistor is open.F3E2Exhaust thermistor has shorted.F3E6Moisture sensor strip is open; this fault code will ONLY appear when in the…F3E7Moisture sensor strip has shorted; this fault code will ONLY appear when in the…F3HHumidity sensor failure.F4-E3Wash motor not running; loose connection in motor circuit and/or faulty wash…F5-E1Door stuck open; door was not latched within 4 seconds of pressing…F5-E2Door stuck closed; control programmed to not start if it suspects the door…F6MW relay failure (Relay 4903 contact may have welded closed).F6-E1Low/no water to dishwasher (mechanical problem).F6-E2Fill valve electrical problem; loose connection in fill valve circuit and/or…F6-E3Suds/air in pump; too many suds, captured wash water, or water leaking from…F6-E4Float switch open; overfill switch stuck in overfill position and/or dishwasher…F6-E7Flowmeter disconnected or damaged.F6-E8Water softener regeneration valve electrical problem; loose connection in regen…F7-E1No heat; control programmed to disable heater if it detects a water heating…F7-E2Heater stuck on; heater drive circuit on the control.F8-E1Slow drain; obstructed drain hose or path.F8-E2Drain motor electrical problem; loose connection in drain motor circuit and/or…F8-E3Drain stuck on; drain motor drive circuit on the control.F8E1No voltage is detected at the water valve relay (only appears in service…NTC OPEN, CALL FOR SERVICEHood thermistor open circuit.NTC SHORT, CALL FOR SERVICEHood thermistor shorted.PFA power failure occurred while the dryer was running.

Service modes (12)

  • Customer Cycle Rapid Advance["Start a customer cycle.","Press HIGH TEMP
  • Customer-Focused Drying Mode Adjustment["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the DONE…
  • Error Code Display (within Service Diagnostics)After entering Service Diagnostics Cycle, errors are displayed in intervals 25-22. Interval 27
  • Error Code Display and Clear["Enter Service Diagnostics Cycle (1-2-3-1-2-3-1-2-3).","Interval 24
  • Rapid Advance (Customer Cycle)After starting a customer cycle, press HI TEMP
  • Rapid Advance ModeAfter starting a cycle, press HI TEMP
  • Sales Demo Mode ExitRun Service Diagnostics Cycle to clear Demo mode.
  • Self-diagnostic / Test Mode["Press and hold OFF/CANCEL while opening the door.","While still holding OFF/CANCEL, unplug the…
  • Self-diagnostic test mode["Press and hold the CANCEL/OFF button while opening the door.","While still holding the CANCEL/OFF…
  • Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the DONE…
  • Service Diagnostics Cycle1
  • User Interface/Control System Test["First activate Service Diagnostic Mode (see above).","Press and release the 1st button used to…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass