mypros+
Model reference

Amana OL-150-4/P96234-6F

Furnace

8 documents39 error codes22 service modes

Available documentation

Tech Sheet

  • Tech Sheet - 980180868 pg
    Covers this model
  • Tech Sheet - W11087920 - Rev A60 pg
    Covers this model
  • Tech Sheet whirlpool dryer W10606148 Rev C60 pg
    Covers this model
  • Tech Sheet - W10403269 - Rev A52 pg
    Covers this model

Installation Guide

  • Installation Instructions16 pg
    Covers this model
  • Installation Instructions24 pg
    Covers this model
  • Installation Instructions20 pg
    Covers this model
  • Installation Instructions32 pg
    Covers this model
MyPros+ Max

Diagnose your Amana OL-150-4/P96234-6F.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (39)

CodeMeaning
:Power failure indicationCLrNo error(s) foundF0Default F codeF1Control failure including UL A/D error(s) and bake/broil range over temperature…F1-E0Key held down too long or key is shorted.F1-E1Keypad keytail not connected.F1-E5CANCEL key drive line open.F1-E6CANCEL key drive line open.F1E1Indicates a Cycle Control Unit (CCU) problem.F2Touch panel failure.F2-E0Temperature sensor opened (R=2875 ohm by spec).F2-E1Temperature sensor shorted (R=825 ohm by spec).F2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; only…F2E2User Interface software errorF3Oven temperature sensor opened or shorted.F3-E2Oven temp too highF3-E3Oven temp too highF3E1Exhaust thermistor is open; temperature drops below 18°F (>50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (<500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms).F3E4Inlet thermistor is shorted; temperature above 391°F (<20 ohms).F3E5Inlet and exhaust thermistors are open; will occur if P14 connector is not…F3E6Moisture sensor strip is open; only appears in service diagnostic mode.F3E7Moisture sensor strip has shorted; only appears in service diagnostic mode.F3HHumidity sensor failure.F4E1No voltage detected at the heater relay; only appears in service diagnostic…F4E3Restricted/low air flow that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at installation.F5Door and door switches do not agree (mismatch between door position and switch…F5-E0Door is open but latch is locked (door switch is open indicating open door, and…
View all 39 error codes
F5-E1Self-clean latch will not lock/unlock.F6MW relay failure (Relay 4903 contact may have welded closed).F6E1Communication between CCU and UI has not been detected (UI to CCU communication…F6E2Communication between CCU and UI has not been detected (CCU to UI communication…FCE1WiFi Module communications lost.L2Low L2 voltage (less than 50V) detected at installation.NTC OPENHood thermistor is open (displays 'NTC OPEN, CALL FOR SERVICE').NTC SHORTHood thermistor is shorted (displays 'NTC SHORT, CALL FOR SERVICE').PFPower failure occurred while the dryer was running.

Service modes (22)

  • Bake Temperature Offset AdjustmentPress BAKE pad for 5 seconds
  • Cavity Size ProgrammingWithin 60 seconds of power up, press the following touchpads in sequence
  • Component Activation / Quick Service Cycle (LCD in Door Models)["Enter Service Diagnostic Mode (LCD in Door) first.","From the DIAGNOSTICS HOME screen, scroll…
  • Customer-Focused Dryness Level Adjustment1
  • Diagnostics ModeWith the oven not in cooking or broiling mode, press Cancel/OFF > Cancel/OFF > START. The display…
  • Fahrenheit to Celsius ConversionPress the BROIL pad for 5 seconds
  • Fault Code CheckPress and hold CANCEL key for 5 seconds.
  • Fault Code DisplayPress and hold CANCEL key for 5 seconds
  • Install Diagnostics1
  • Key Activation & Encoder Test (Console Models)["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
  • Loads Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Within 5 seconds: Press…
  • Self-Diagnostic / Test Mode["1
  • Self-Diagnostic Test Mode["Press and hold the OFF/CANCEL button while opening the door.","While still holding the OFF/CANCEL…
  • Service Diagnostic Mode1. Ensure dryer is in standby mode (plugged in with all indicators off). 2. Select any three…
  • Service Diagnostic Mode (Console Models)["Ensure the dryer is in standby mode (plugged in with all indicators off).","Select any three (3)…
  • Service Diagnostic Mode (LCD in Door Models)["Ensure the dryer is in standby mode (plugged in with all indicators off).","Open and close the…
  • Service Test Mode (Console Models)["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
  • Software Version Display1
  • Software Version Display (Console Models)["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…
  • Temperature Adjustment ModePress and hold BAKE key for 5 seconds
  • User Interface Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
  • User Interface/Control System Test1. Activate Service Diagnostic Mode. 2. Press and release the 1st button used to activate Service…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass