Model reference

Amana OS-100/P96237-1F

Name: Amana OS-100/P96237-1F
Brand: Amana

Furnace

6 documents61 error codes9 service modes

Available documentation

Tech Sheet

Tech Sheet - W10136477 - Rev A_W101364778 pg
Covers this model
Tech Sheet - W10268751 - Rev A_W1026875110 pg
Covers this model
Tech Sheet - W10268744 - Rev A10 pg
Covers this model
W10751162A.fm12 pg
Covers this model
Tech Sheet - 820601020 pg
Covers this model
Tech Sheet - 82058778 pg
Covers this model

MyPros+ Max

Diagnose your Amana OS-100/P96237-1F.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Amana Furnace

: on my Amana OS-100/P96237-1F

M+

Flashing colon indicates a power

From Tech Sheet W18223242, p.14:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (61)

View all 61 error codes

9-2Diverter 9-3Diverter 9-4Diverter F1-E1Control detected K2 pilot relay stuck closed.F1-E2Damaged or corrupted memory on control board; incompatible software components…F10-E1Dispenser electrical problem; loose connection in dispenser circuit and/or open…F10-E3Drying fan error; loose connection in fan circuit and/or open fan motor.F2Touch panel failure.F2-E1Control detected stuck key(s) in keypad or keypad connection.F2-E2User interface cannot communicate with main control; loose user interface…F3-E1Open connector or component in temperature sensing circuit; open or faulty…F3-E2Incoming water temperature above 167°F (75°C), or shorted connection/component…F3-E3OWI calibration failure; dirty water backs into dishwasher after draining or…F3HHumidity sensor failure.F4-E3Wash motor not running; loose connection in motor circuit and/or faulty wash…F5-E1Door stuck open; door was not latched within 4 seconds of pressing…F5-E2Door stuck closed; control programmed to not start if it suspects the door…F6MW relay failure (Relay 4903 contact may have welded closed).F6-E1Low/no water to dishwasher (mechanical problem).F6-E2Fill valve electrical problem; loose connection in fill valve circuit and/or…F6-E3Suds/air in pump; too many suds, captured wash water, or water leaking from…F6-E4Float switch open; overfill switch stuck in overfill position and/or dishwasher…F6-E7Flowmeter disconnected or damaged.F6-E8Water softener regeneration valve electrical problem; loose connection in regen…F7-E1No heat; control programmed to disable heater if it detects a water heating…F7-E2Heater stuck on; heater drive circuit on the control.F8-E1Slow drain; obstructed drain hose or path.F8-E2Drain motor electrical problem; loose connection in drain motor circuit and/or…F8-E3Drain stuck on; drain motor drive circuit on the control.NTC OPEN, CALL FOR SERVICEHood thermistor open circuit.NTC SHORT, CALL FOR SERVICEHood thermistor shorted.

Service modes (9)

Customer Cycle Rapid Advance["Start a customer cycle.","Press HIGH TEMP
Error Code Display (within Service Diagnostics)After entering Service Diagnostics Cycle, errors are displayed in intervals 25-22. Interval 27
Error Code Display and Clear["Enter Service Diagnostics Cycle (1-2-3-1-2-3-1-2-3).","Interval 24
Rapid Advance (Customer Cycle)After starting a customer cycle, press HI TEMP
Rapid Advance ModeAfter starting a cycle, press HI TEMP
Sales Demo Mode ExitRun Service Diagnostics Cycle to clear Demo mode.
Self-diagnostic / Test Mode["Press and hold OFF/CANCEL while opening the door.","While still holding OFF/CANCEL, unplug the…
Self-diagnostic test mode["Press and hold the CANCEL/OFF button while opening the door.","While still holding the CANCEL/OFF…
Service Diagnostics Cycle1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass