Model reference

Amana OS-125/P96291-3F

Furnace

3 documents40 error codes5 service modes

Available documentation

Tech Sheet

Tech Sheet 8204950 WP MW Tech Sheet GH9177xlt 212 pg
Covers this model

Tech Tip

Instruction Sheet - 818396912 pg
Covers this model
Instruction Sheet - 818472212 pg
Covers this model

MyPros+ Max

Diagnose your Amana OS-125/P96291-3F.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Amana Furnace

: on my Amana OS-125/P96291-3F

M+

Flashing colon indicates a power

From Tech Sheet W12928919, p.51:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (40)

CodeMeaning

:Flashing colon indicates a power failure has occurred.1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board, or incompatible software…10-1Dispenser electrical problem 10-3Drying fan error 2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface cannot communicate with main control 3-1Open connector or component in temperature sensing circuit (open or faulty…3-2Shorted connection or component in temperature sensing circuit, shorted or…3-3OWI calibration failure due to OWI sensor failure or drain hose check valve not…4-3Wash motor not running due to loose connection in motor circuit, faulty wash…5-1Door stuck open 5-2Door stuck closed 6-1Low or no water 6-2Fill valve electrical problem 6-3Suds or air in pump causing repeated wash periods.6-4Float switch open 6-7Disconnected or damaged flowmeter.6-8Regen valve electrical problem 7-1No heat 7-2Heater stuck on 8-2Drain motor electrical problem 8-3Drain motor stuck on 9-1Diverter can't find position 9-2Diverter stuck on 9-3Diverter disk in sump is missing.9-4Lower spray arm error F0No error condition present.F10Display error.F2Membrane switch failure.

View all 40 error codes

F2KKey or foil pressed more than 1 minute.F2TTouch panel pressed more than 1 minute.F3HHumidity sensor out of range.F3TTemperature sensor out of range.F6Microwave relay failure.F7Power to magnetron interrupted.F9CE2PROM CheckSum error.F9EE2PROM empty.F9ME2PROM missing.F9WE2PROM write error.

Service modes (5)

Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
Test Mode (Self-Diagnostic)["Press the clock key.","Press keys 1, 2, and 3 on the keyboard.","Touch AM/PM on the touch screen…
test_mode["Press the clock key.","Press keys 1, 2 and 3 on the keyboard.","Touch AM/PM on the touch screen…
Touch Panel and Electronic Control Self-Diagnostic Test Mode["Press and hold CANCEL while opening the door.","While still holding the CANCEL button, unplug the…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass