mypros+
Model reference

Amana OS-250/P96317-3F

Furnace

4 documents37 error codes9 service modes

Available documentation

Tech Sheet

  • tech-sheet-W10859290-RevA.pdf16 pg
    Covers this model
  • Tech Sheet 8204950 WP MW Tech Sheet GH9177xlt 212 pg
    Covers this model

Tech Tip

  • Instruction Sheet - 818472212 pg
    Covers this model

Installation Guide

  • Instrucciones de instalacion2 pg
    Covers this model
MyPros+ Max

Diagnose your Amana OS-250/P96317-3F.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (37)

CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board, or incompatible software…10-1Dispenser electrical problem10-3Drying fan error2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface cannot communicate with main control3-1Open connector or component in temperature sensing circuit (open or faulty…3-2Shorted connection or component in temperature sensing circuit, shorted or…3-3OWI calibration failure due to OWI sensor failure or drain hose check valve not…4-3Wash motor not running due to loose connection in motor circuit, faulty wash…5-1Door stuck open5-2Door stuck closed6-1Low or no water6-2Fill valve electrical problem6-3Suds or air in pump causing repeated wash periods.6-4Float switch open6-7Disconnected or damaged flowmeter.6-8Regen valve electrical problem7-1No heat7-2Heater stuck on8-2Drain motor electrical problem8-3Drain motor stuck on9-1Diverter can't find position9-2Diverter stuck on9-3Diverter disk in sump is missing.9-4Lower spray arm errorF0No error condition present.F10Display error.F2KKey or foil pressed more than 1 minute.F2TTouch panel pressed more than 1 minute.
View all 37 error codes
F3HHumidity sensor out of range.F3TTemperature sensor out of range.F7Power to magnetron interrupted.F9CE2PROM CheckSum error.F9EE2PROM empty.F9ME2PROM missing.F9WE2PROM write error.

Service modes (9)

  • Customer Program Fast Forward ModeAfter starting a customer program, press HI TEMP
  • Error History ClearDuring the service diagnostic program at the error display interval, press the HI TEMP (high…
  • Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
  • Service Diagnostic Program1
  • Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
  • Test Mode (Self-Diagnostic)["Press the clock key.","Press keys 1, 2, and 3 on the keyboard.","Touch AM/PM on the touch screen…
  • test_mode["Press the clock key.","Press keys 1, 2 and 3 on the keyboard.","Touch AM/PM on the touch screen…
  • Touch Panel and Microcomputer Board Test (Self-Diagnostic)["Press the clock key.","Press keys 1, 2, and 3 on the keyboard.","Touch AM/PM on the touch screen…
  • Touch Panel and Microcomputer Board Test Mode (Self-Diagnostic)["Press the CLOCK key.","Touch 'Hours' on the touch screen and set hours to '1'.","Touch 'Minutes'…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass