mypros+
Model reference

Amana OU-150-UA

Furnace

6 documents71 error codes15 service modes

Available documentation

Service Manual

  • km-29-whrlpl96 pg
    Covers this model
  • Job Aid - 8178545 (KM-29)96 pg
    Covers this model

Tech Sheet

  • Tech Sheet - W11597123 - Rev A2 pg
    Covers this model
  • Tech Sheet - 820490312 pg
    Covers this model
  • TechSheet-W10851840-RevA_W1085184016 pg
    Covers this model

Installation Guide

  • Installation Instructions8 pg
    Covers this model
MyPros+ Max

Diagnose your Amana OU-150-UA.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (71)

CodeMeaning
:Flashing colon indicates a power failure has occurred.F0No error present.F0E1Load detected in drum during Clean Washer cycle.F0E2OversudsF0E4High temperature error during wash cycle.F0E5Off balance load detected.f1 e1Primary control failure.F1.E1Relay control board defective.F10Display error.F1E0EEPROM communication error.F1E1Main relay open or shorted.F1E2MCU over- or under-voltage error.F1E4Microwave relay failure (Relay 4903 on PCBA).F1E5Sensor out of range.F1E7PCB thermistor open or shorted.F2Touch panel failure.f2 e1Stuck button or user interface mismatch (only appears in service diagnostic…F2.H1Hood keys stuck.F2.H2Hood/light switch defective.F2.Q1Not reading keypad inputs.F2E0Keypad disconnected.F2E1Touch panel failure.F2E2Cancel key error.F2KKey or foil pressed more than 1 minute.F2TTouch panel pressed more than 1 minute.f3 e1Exhaust thermistor is open.f3 e2Exhaust thermistor has shorted.f3 e6Moisture sensor strip is open (only appears in service diagnostic mode).f3 e7Moisture sensor strip has shorted (only appears in service diagnostic mode).F3.H1Humidity sensor failure.
View all 71 error codes
F3.T1UIB (user interface board) thermistor failure.F3.T2FC (forced convection) thermistor failure.F3.T4Magnetron thermistor failure.F3E0Main sensor open or shorted.F3E1Pressure sensor signal missing or out of range.F3E2Wash NTC (thermistor) open or shorted.F3E5Dry NTC faultF3E6Accelerometer error.F3HHumidity sensor out of range.F3TTemperature sensor out of range.F4E1Wash heater relay error or no feedback signalF4E2Wash heater relay error.F5E0Door and switches do not agree (Clean modeF5E2Door lock failure.F5E3Door unlock failure.F5E4Door not open error.F6MW (microwave) relay failure.F6E1No communication from the HMI detected by ACU.F6E2No communication from the ACU detected by the HMI.F6E3No communication from the MCU detected by the ACU.F7Power to magnetron interrupted.F7E10Motor disconnected error.F7E12MC/MCU overload.F7E2MC/MCU over temperature error or over current error/internal failure.F7E8MC/Motor over temperature error.F7E9Motor will not turn (locked rotor).F7EAMotor disconnected error (alternate hex display of F7E10).F7ECMC/MCU overload (alternate hex display of F7E12).f8 e1No voltage detected at the water valve relay (steam models only, only appears…F8E1Water inlet valve failure.F8E3Overflow condition detected.F9Relay control board communications error.F9.QTouch communication error between UIB and touch panel board.F9CE2PROM CheckSum error.F9EE2PROM empty.F9E1Long drainF9ME2PROM missing.F9WE2PROM write error.NTC OPEN, CALL FOR SERVICEHF NTC thermistor is open.NTC SHORT, CALL FOR SERVICEHF NTC thermistor is shorted.pfPower failure occurred while the dryer was running.

Service modes (15)

  • Customer-Focused Drying Mode Adjustment1
  • demo_mode["On the Main Menu, touch 'Settings & Info.'","On Settings & Info screen, touch 'Demo Mode.'","The…
  • diagnostic["Unplug microwave oven or disconnect power.","Open the microwave oven door.","Press and hold…
  • Diagnostics / Auto Test1. Press CANCEL > CANCEL > START to enter Diagnostics mode. 2. Press the 'up' arrow, the '+' (plus)…
  • Fault/Error Code Display["Enter Service Diagnostic Mode
  • Human-Machine Interface Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
  • learning_mode["Oven must be off.","On the Main Menu, touch 'Settings & Info.'","On Settings & Info screen, touch…
  • Quick Diagnostic Test["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
  • Self-Diagnostic Test Mode["Plug in microwave oven or reconnect power.","Press CANCEL button to enter standby (display shows…
  • Self-diagnostic test mode (Touch Panel and PCBA Test)["Press and hold the OFF/CANCEL button while opening the door.","While still holding the OFF/CANCEL…
  • Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Wait 30 seconds after…
  • Software Version Display["First activate Service Diagnostic Mode.","Press and hold the 2nd button used to activate Service…
  • Touch Panel and Microcomputer Board Self-Diagnostic Test Mode["Press the Clock key.","Press keys 1, 2, and 3 on the keyboard.","Touch AM/PM on the touch screen…
  • Touch Panel and PCBA Self-Diagnostic Test Mode["Press and hold the OFF/CANCEL button while opening the door.","While still holding the OFF/CANCEL…
  • User Interface/Control System TestAfter activating Service Diagnostic Mode, press and release the 1st button used to activate Service…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass