Model reference
Amana YY-120-TA
Furnace
7 documents75 error codes10 service modes
Available documentation
Tech Sheet
- Wiring Diagram - W10668584 - Rev A8 pg
Service Manual
- Job Aid - 4322536A (G-20)76 pg
Tech Tip
- Instruction Sheet - 85290006 pg
- Instruction Sheet - 397971412 pg
Installation Guide
- Installation Instructions64 pg
- Installation Instructions28 pg
- Installation Instructions32 pg
MyPros+ Max
Diagnose your Amana YY-120-TA.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (75)
CodeMeaning
3 beepsThermistor or wire harness is either shorted or open, detected when Push To…F0 E0Factory defaultF0-E0Default F codeF0E0No error(s) foundF1EEPROM Communications error.F1 E0EEPROM communications error.F1 E1EEPROM checksum error.F1 E2UL A/D error(s).F1 E4Model ID error.F1 E6Latch signal mismatch error.F1-E0EEPROM Communications failure.F1-E1Electronic control malfunction (E1).F1-E2EEPROM Checksum Failure.F1-E3UL A/D Error(s).F1E0Replace oven User InterfaceF1E1Oven Appliance Manager failure (not applicable for lower oven on double oven…F1E4Microwave ACU PCBA failure.F2 E0Shorted key.F2 E1Key tail unplugged.F2-E0Shorted Key detected.F2-E1Key Tail Unplugged.F2-E3Electronic control malfunction (E3).F2-E4Electronic control malfunction (E4).F2-E5Electronic control malfunction (E5).F2E0Keypad disconnected.F2E1Stuck key failure.F2E2LED error.F2E3Keypad hardware failure.F3 E0Oven sensor openedF3 E1Oven sensor shortedView all 75 error codes
F3 E2Bake/broil range over temperature.F3 E3Clean range over temperature.F3 E4Oven sensor openedF3 E5Oven sensor shortedF3 E6Warming drawer sensor open.F3 E7Warming drawer sensor shorted.F3-E0Oven temperature sensor opened (open circuit).F3-E0/E1Temperature sensor opened (lower cavity).F3-E1Oven temperature sensor shorted.F3-E2Bake range over temperature condition.F3-E3Clean range over temperature condition.F3E0Upper oven sensor open, shorted or grounded.F3E1Lower oven sensor open, shorted or grounded.F3E2Warming drawer sensor shorted (oven is not equipped with this feature…F3E3Meat probe shorted.F4-E0Meat probe shorted.F4E1Cavity temperature sensor failure.F4E4Humidity sensor error.F4E9Smart pop error.F5 E0Door switches do not agree.F5 E1Door latch not operating.F5-E0Door and switches do not agree (door position mismatch).F5-E1Door latch not operating.F5-E2Latch error during clean cycle.F5E0Door and latch switch do not agree.F5E1Door latch not operating.F6-E0Self-clean latch will not lock.F6-E1Self-clean latch will not unlock.F6E0ACU PCBA communication failure.F6E1Cook oven over temperature.F6E2Clean oven over temperature.F6E3Mini oven/warm drawer over temperature (not for built-in ovens).F6E4User interface / Appliance Manager mismatch.F6E5Cavity size is incorrect.F8-E0Oven over temperature while door open and latch lock.F8-E1Oven over temperature while door open and latch unlock.F8-E2Oven over temperature while door open and latch lock.F8-E3Oven over temperature while door open and latch unlock.F8-E4Oven over temperature while door closed and latch unlock.F8E0Low fan speed underspeedF8E1Low fan speed overspeedF8E2High fan speed underspeedF8E3High fan speed overspeedF8E5Exhaust air temperature sensor failure.SABOven is in Sabbath Mode.
Service modes (10)
- Bake Temperature Calibration AdjustmentPress and hold BAKE pad for 5 seconds. Current offset (if any) is shown in 3-digit display; CAL is…
- Bake Temperature Offset Adjustment1
- Damp Dry Test["Begin with an empty dryer and clean lint screen.","Set Timer to DAMP DRY.","Set Fabric…
- Diagnostics Mode["Plug in microwave oven or reconnect power.","Press CANCEL button to reach standby (display shows…
- Factory Test["Open the dryer door.","Set Fabric Care/Temperature switch to AIR FLUFF.","Set Signal switch to…
- Fahrenheit to Celsius ConversionPress the BROIL pad for 5 seconds
- Last Error Code RecallPress and hold CANCEL/OFF key for 5 seconds until last error code is displayed.
- Sabbath Mode exitSAB will appear in digital display when oven is in Sabbath Mode.
- Temperature Adjustment (Calibration)Press and hold BAKE pad for 5 seconds. Current offset (if any) is shown in 3-digit display. CAL is…
- Temperature Calibration AdjustmentPress and hold BAKE pad for 5 seconds
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana furnace models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass